The topsoil sand at Yanda was severely repellent (Figure 1, left), as measured by the molarity of ethanol droplet test (MED). Clay spreading and tillage (either combined or separated) significantly reduced the severity of water repellency. When the subsoil clay was not incorporated by tillage or was incorporated using an off-set disc, the soil water repellency generally decreased with an increasing amount of subsoil clay. However, low-repellency (MED<1) was obtained only at rates over 150 t/ha of subsoil.

In contrast, spading (either at standard speed of the tractor or at half speed) was the most effective method for the alleviation of soil water repellency. In these treatments, the MED values were completely reduced to zero (non-repellent soil) and, most importantly, this was achieved independently from the presence, or not, of clay-rich subsoil. The significant reduction of the soil water repellency however did not convert to better plant establishment measured five weeks after sowing (Figure 1, Right).  This result could be explained by the wetter than usual weather recorded during April-May 2016 that reduced the impact of the soil water repellency on plant establishment. Nevertheless, tiller counts collected five weeks after plant counts showed a significant effect of tillage on the number of tillers. In particular, the spader treatments (standard and ½ speed) had the most tillers while the control had the fewest.

This trend was repeated with the barley grain yields at harvest time (Figure 2). Both tillage and rate of clay spreading, significantly improved grain yield in comparison to the control treatments (no clay and no tillage). The lowest yield were recorded in the control treatments and in the off-set tillage only (no clay) with an average of 1.41 t/ha and 1.36 t/ha respectively. The shallow tillage (or incorporation) using off-set discs did not yield significantly differently from the treatments with no incorporation at any given rate of subsoil clay. Clay spreading at 250 t/ha followed by spading at standard speed produced the highest yield on average (2.93 t/ha). Nonetheless, all treatments with spading (standard and ½ speed) were able to yield over 2.5 t/ha, even without the addition of subsoil clay (Figure 2). 

Field observations showed that the trial was also affected by frost, which explained the lower than expected yields. Head samples were collected in early November 2016 from all the treatments (except spading at ½ speed) for the assessment of frost induced sterility (FIS= number of sterile florets / total number of florets) and the results are shown in Figure 3.

The results on FIS showed that frost damage might be one of the main reasons of low yields and responsible of the large yield differences between treatments. The control treatments and the off-set treatment (no clay) had over 60% frost induced sterility. Even though increasing amounts of subsoil clay significantly reduced FIS (Figure 3c), the treatments with no incorporation or with incorporation by off-set discs still recorded FIS values above 50%. Spading was the most effective treatment to significantly reduce frost damage to below 40%, regardless of the presence or not of subsoil clay (Figure 3a and b).

Spading was the most successful treatment in this first year of the trial at Yanda. Most importantly, spading was able to produce the highest yields and significantly reduce the frost damage regardless of the addition subsoil clay. This was particularly evident when estimating the simple return of investments on the first year of the trial (ROI= ($/ha gain – $/ha total direct costs) / $/ha total direct costs), based on the mean values presented in Table 3. Because of the high crop-specific costs with barley at Yanda (500 $/ha) and the yield reduction due to frost, spading alone at standard speed was the only treatment that gave a positive ROI on the first year (+0.4 $/ha) followed by negative ROI with spading at ½ speed (-0.18 $/ha) and the control (-0.35 $/ha). These estimates are indicative only, as indirect costs and interests on the initial capital investment are not included in the calculations. For more accurate estimates of ROI, yield results from multiple seasons and crops will be collected in the next 3 years.

 

Grain yield losses of up to 40% can be caused by clethodim at particular rates and timings. Early application timings were the best to avoid crop damage. Variation does exist between herbicide tolerant crop types (Conventional, Clearfield and TT) and their level of sensitivity to clethodim

• An intended comparison between native ryegrass and Safeguard ryegrass became a comparison between what is probably Italian ryegrass and Safeguard ryegrass.
• It was observed that in early November sheep grazed the Italian ryegrass in preference to the Safeguard ryegrass.

• In the absence of stripe rust but the presence of leaf and stem rust and powdery mildew, an integrated fungicide strategy is critical for maximising yield and grain quality.
• Early application of fungicide (e.g. seed treatment or in-furrow) alone is insufficient to optimise grain yield and quality.

• Break crops faced a range of tough environmental conditions in the Mallee in 2015 including multiple frost and heat shock events.
• Timely rainfall in April and hence early sowing resulted in excellent biomass production with most crop options producing on average more than 2 t DM/ha and several break crop options producing greater than 2.5 t DM/ha.
• The highest grain yields tended to be crops with the quickest maturity such as lentils (0.73 t/ha), vetch (0.64 t/ha) and field peas (0.63 t/ha).
• High value crops such as lentils and vetch were highly profitable due to both excellent prices and reasonable grain yields. (v) Break crop productivity and profitability was very different between common Mallee soil types.

• Break crops faced a range of tough environmental conditions in the Mallee in 2015 including multiple frost and heat shock events.
• Timely rainfall in April and hence early sowing resulted in excellent biomass production with most crop options producing on average more than 2 t DM/ha and several break crop options producing greater than 2.5 t DM/ha.
• The highest grain yields tended to be crops with the quickest maturity such as lentils (0.73 t/ha), vetch (0.64 t/ha) and field peas (0.63 t/ha). 
• High value crops such as lentils and vetch were highly profitable due to both excellent prices and reasonable grain yields.
• Break crop productivity and profitability was very different between common Mallee soil types.

• Break crops faced a range of tough environmental conditions in the Mallee in 2015 including multiple frost and heat shock events.
• Timely rainfall in April and hence early sowing resulted in excellent biomass production with most crop options producing on average more than 2 t DM/ha and several break crop options producing greater than 2.5 t DM/ha.
• The highest grain yields tended to be crops with the quickest maturity such as lentils (0.73 t/ha), vetch (0.64 t/ha) and field peas (0.63 t/ha).
• High value crops such as lentils and vetch were highly profitable due to both excellent prices and reasonable grain yields.

• Varieties with the longest coleoptiles on average were Cutlass and Yitpi with 81 mm and 80 mm, respectively.
• Varieties with the shortest coleoptiles on average were Cobra and Wedgetail with 61 mm and 62 mm, respectively.
• Increasing soil temperature had a negative impact on coleoptile length with an average length of 67 mm recorded at 21°C, compared to 72 mm at 16°C.

• Double knock applications of group H containing herbicides followed by paraquat seven days later appear to be very effective in controlling early flowering common sowthistle.
• Paraquat and Velocity were also very effective as standalone treatments in controlling early flowering common sowthistle.

• Double knock applications of some group H containing herbicides followed by paraquat seven days later appear to be a viable alternative to double knocking with Tordon 75D followed by paraquat for the control of early flowering flaxleaf fleabane.
• The most effective group H containing herbicides in combination with paraquat as double knock treatments were Precept, Balance and Velocity in order of effectiveness of their control of early flowering flaxleaf fleabane.

• All of the herbicides examined appear to work well when tank mixed with paraquat to control early flowering common sowthistle.
• However, paraquat alone also provided excellent control of early flowering common sowthistle which questions the value of tank mixes with other herbicides.

• Tank mixing group H and H/I herbicides with paraquat (Group L) for the control of early flowering fleabane generally only provided moderate efficacy in this experiment.
• Tordon 75-D (Group I) mixed with paraquat and Velocity (Group H/C) mixed with paraquat, however, provided reasonable control at 89% and 81%, respectively.
   

• Some early flowering varieties developed significantly higher levels of sclerotinia stem rot infection.
• Variety response to infection and yield could be relative to other factors such as infection timing and plant
biomass.

Using the highest label rate of either Aviator Xpro or Prosaro in the first application for sclerotinia lowered the level of sclerotinia infection and recorded a higher $ROI/ha in this trial. Increasing the rate of fungicide increases early activity on active disease but will also increase the length of protection from reinfection. 

The use of higher rates under high sclerotinia disease pressure is recommended not only in a single spray application to extend the window of protection but as recorded in this trial it can provide benefits to a two spray strategy. Improvements in length and strength of sclerotinia control from the use of a higher rate in the first application have been recorded across multiple commercial trials conducted by Bayer Crop Science across Australia in the 2016 season.

• Revenue produced a significantly higher grain yield than Mackellar although this was not significantly different to H150.1 and Tennant. In addition Revenue tends to have higher dry matter prodution than Mackellar. In this trial the latter may have been more susceptible to the waterlogging.
• The white grained CSIRO line H150.2 continues to produce high grain yields in Tasmania and has now also demontrated potential as a dual pupose crop. It will be suitable for an earlier dual purpose sowing as it is later flowering than both Mackellar and Revenue.
• Preston showed good early vigour but it will flower too early for more typical dual purpose sowing times in Tasmansa, e.g. March.

• All three seeders have resulted in successful establishment of sub-tropical grasses at the paddock scale.  This reinforces that successful establishment can be achieved with a range of seeding machinery providing the basic principles are followed: i.e. furrow sowing, press wheels, precise shallow seeding together with wide row spacing.
• The disc seeder appeared to have the least soil disturbance, with less loose soil on the soil surface after seeding, but had slightly more sand infill.  This may be due to steep side walls and a relatively narrow furrow, while the seeders with tynes created larger – wider furrows, so sand moving into the furrow was spread over a wider base.  The Case-International combine with a single point had the lowest sand infill.
• The disc seeder resulted in the highest establishment of panic grass, but in late October many of these plants were still small seedlings and subsequently many died over summer.  As number of plants, size and health of plants need to be taken into account, the disc machine may not provide an overall advantage as the proportion of healthy plants was much less. Visually, the Case-International combine appeared to produce a thicker stand; this was most likely due to the higher number of medium to large sized plants when compared to the other machines. 
• The knockdown did not completely kill the brome grass which subsequently recovered and competed with the emerging perennial grass seedlings in early spring.  Combined with dry conditions in October (5 mm) the perennial grass seedlings were struggling in late October.  More favorable seasonal conditions in November and December enabled the grasses to establish.  The scalping points on the John Shearer were able to reduce the impact of brome grass more successfully than the other seeders.
• Persistence will be measured over late summer until the break of the season.  This machinery demonstration trial will be the focus of an extension video which features the producers describing the modifications to their seeders.

Overall, early growth was a function of a number of constraints. In the fully retained stubble plots plant establishment was poor due to large straw windrows creating major problems at sowing and mice damage. In surface stubble treatments lower soil temperatures and higher populations of vulpia resulted in reduced plant vigour. Where stubble was fully retained this effect was less than when most stubble was removed through cutting and baling.

• Axe was the highest yielding wheat variety, at 1.13t/ha.
• Generally the early maturing varieties were higher yielding compared to the late maturing varieties.

• KING ROCK fell in a hole early, ran up quickly and often looked very heat and moisture stressed.
• LONGREACH COBRA did not handle a dry year. It did not appear robust or durable in a dry warm season.
• CORACK and MACE handled drought stress well.
• CALINGIRI and MAGENTA looked the most durable and robust all year.
• CALINGIRI again proved very adaptable.

Note: This trial was an unreplicated demonstration with observations/assesments based on one plot per treatment only, and as such results may not be definitive.

Increased use of grass selective herbicides in many farming systems has caused increased selection pressure for herbicide resistance in grass weed populations such as annual ryegrass and brome grass. Work conducted by Bill Roy (Agricultural Consulting & Research Services Pty Ltd, York) with GRDC support demonstrates that managing herbicide resistance requires a diversified approach using a number of different tools. Manipulating canopy through seeding rates and row spacing is one of the options being explored by the BCG.

Increased use of grass selective herbicides in many farming systems has caused increased selection pressure for herbicide resistance in grass weed populations such as annual ryegrass and brome grass. Work conducted by Bill Roy (Agricultural Consulting & Research Services Pty Ltd, York) with GRDC support demonstrates that managing herbicide resistance requires a diversified approach using a number of different tools. Manipulating canopy through seeding rates and row spacing is one of the options being explored by the BCG.

• Variety: there was no difference between the yield of Digger and Northfield (0.56 vs 0.57 t/ha respectively)
• Row spacing: there was no significant difference in the yield of lentils sown at 18 cm (7") or 36 cm (14") (0.59 vs 0.54 t/ha respectively). However, the crop sown at 18cm (7") was much easier to harvest and stood up better.
• Sowing rate: there was a significant negative effect of sowing rate on yield - the 50kg sowing rate had the higher yield compared to the 100kg/ha sowing rate (0.62 vs 0.51 t/ha respectively).

• The extremely late break to the season highlighted maturity differences very clearly. 
• The long season trial was sown on the same day as the main season trial, favouring heavily the short season varieties.

• Overall imposing a fallow allowed for a small amount of extra water to be stored in the soil and a small amount of extra nitrogen. As a result there was a small yield gain of 0.2 t/ha in 2012. 
• In this trial the fallow treatment was planted then sprayed out in August to replicate what is known as an ‘opportunistic’ fallow compared to a ‘strategic’ fallow where no crop is planted for 18 months. 18 month fallows would have different results to the ones reported here.
• Other benefits of fallow that were not recorded in this trial but could have contributed to the yield gain are improved weed control, disease breaks and opportunity for early sowing. 

• Soil and solution culture studies were conducted to examine the relative contribution of different mechanisms of zinc efficiency at the whole plant level in bread and durum wheat during early vegetative stage.
• While there are a number of mechanisms of zinc efficiency, zinc uptake appears to be the most important mechanism • Seed zinc remobilisation and root to shoot translocation do not appear to be important to zinc efficiency.
• Visual scores of zinc deficiency were significantly correlated with zinc efficiency, and they provide a useful criterion for an initial screen of zinc efficiency.
• This study was based on vegetative growth and the conclusions need to be verified under field conditions.
• The percentage deviation technique provided a straight forward means of comparing the relative effects of different components of zinc efficiency and the method could be extended to studies that use grain yield as the measure of zinc efficiency.

• All pre-emergent herbicides provided excellent early control of ryegrass (≥86%) & good crop safety under the knife-point press wheel system.
• Combination of trifluralin & Avadex Xtra followed by PSPE Boxer Gold provided greatest residual control, controlling more than 98% of ryegrass 12 weeks after sowing.
• Boxer Gold applied PSPE has been shown to provide some additional in-row controlof ryegrass.

Early application of selective herbicide (Group 1, A) gave excellent control of barley grass. While fewer barley grass plants meant less pasture biomass, it’s important to remember that the seeds on the mature barley grass would injure livestock. Further, these barley grass plants could host cereal crop disease.

Spray topping prevented viable seed set of barley grass while leaving the greatest pasture biomass.

Good barley grass control in the 2019 pasture was still evident in the 2020 and 2021 crops.

Late sowing of barley in 2020 (delayed 4 weeks) was relatively ineffective in controlling barley grass and crop yield was slightly reduced.

Late sowing of oats in 2021 (delayed 7 weeks) gave excellent weed control, but the crop yield was severely reduced.

The trial establishment was variable early due to some non-wetting soil and the crop was sown too deeply due to furrow fill from significant rain after sowing. Early crop vigour as a result was low with blackleg further reducing plant establishment; this coupled with high levels of Vegetable beetle damage also reduced the evenness of the plots.

According to the DAFWA sporacle model spore maturity occurred on approximately the 22nd May which meant this trial was at very high risk of significant disease risk as emergence coincided with high spore levels being released from last year’s stubble.

• Excellent annual ryegrass control (>85%) with propyzamide either as split application (IBS followed by PSPE) or as a mixture with tri-allate.
• Atrazine also gave effective control this season with rainfall assisting activity (>79%).
• Early crop vigour was suppressed with Outlook & the higher split rate (1 kg/ha IBS followed by 1 kg/ha PSPE) of propyzamide.
• UAN at 20 kg/ha caused some leaf burning, however the crop recovered.

• A Predicta B sample taken from the site indicated a medium risk of rhizoctonia although patches did not express during the season.
• Early establishment across the site was severely impacted by non-wetting affected all plots across the trial with the worst of it commencing around plot 215 and increasing in severity throughout replicate 3.  Early dry conditions further staggered the crop emergence.
• Good rains through late July and into early August ensured the crop was growing well albeit patchy across the trial with high levels of disease present at both the Z31 and Z39 applications. Only 48.9 mm of rain fell from the second Z39 application to the end of October reducing the benefits to yield of the different fungicide treatments.
•  Increasing variability in the trial due to the sub-soil issues from plot 215 into replicate 3 was a significant factor. Yield data should be treated with caution due to the variability of the site with disease control is the most accurate assessment of treatment efficacy.

• Control of net form net blotch using effective fungicides resulted in yield increases of up to 1.0 t/ha compared to nil treatments.
• Two strategic fungicide applications during early-mid growth stages (before end of August) – suppressed disease development and provided control comparable to four applications made every 2-4 weeks from early August.
• Tilt, Amistar Xtra, Opera and Prosaro were effective for control of net form of net blotch.

• Control of net form net blotch using effective fungicides resulted in yield increases of up to 1.0 t/ha compared to nil treatments.
• Two strategic fungicide applications during early-mid growth stages (before end of August) – suppressed disease development and provided control comparable to four applications made every 2-4 weeks from early August.
• Tilt, Amistar Xtra, Opera and Prosaro were effective for control of net form of net blotch.

• A two spray or double knock strategy (including cultivation or another non-herbicide treatment) is often required for complete control in fencelines with the first application early in the season followed by another one later in the season (after the seeding and post-harvest operations are over).
• Tank mixes of residual herbicides plus a knockdown give the best control for the first application.
• A single application of a mixture of Uragan® (bromacil) and paraquat early in the season gives excellent weed control on fencelines.
• The addition of Alliance® (mixture of amitrole and paraquat) as the knockdown gives good broadleaf control.
• Glyphosate can still be used but intensive monitoring and complete seed set control is required to prevent resistance from developing.

 

• In the 2001 season there was no benefit from the application of an alphacypermethrin insecticide application to barley and lentil crops.
• The dry summer of 2000/2001 resulted in very few host plants for aphids and virus diseases and threshold levels for disease carry over potential were not reached.
• In wet summers with many host plants surviving it is possible that preventative spraying with alphacypermethrin could be worthwhile.

In the 2001 season there was no benefit from the application of an alphacypermethrin insecticide application to barley and lentil crops. The dry summer of 2000/2001 resulted in very few host plants for aphids and virus diseases and threshold levels for disease carry over potential were not reached. In wet summers with many host plants surviving it is possible that preventative spraying with alphacypermethrin could be worthwhile.

In the 2001 season there was no benefit from the application of an alphacypermethrin insecticide application to barley and lentil crops. The dry summer of 2000/2001 resulted in very few host plants for aphids and virus diseases and threshold levels for disease carry over potential were not reached. In wet summers with many host plants surviving it is possible that preventative spraying with alphacypermethrin could be worthwhile.

This trial looked at protecting the crop from excessive sun and wind during the spring when crops are flowering and setting seed by covering it in shade cloth in early September. It was expected that this would improve yield and grain size but in fact it had the opposite effect with reduced yields and poor grain quality.

• Two years of full wild oat control did not exhaust the seedbank to a manageable level.
• A selective post emergent herbicide or an early hay cut were the most effective strategies for reducing the wild oat seedbank.

• One year of full wild oat control reduced the wild oat seedbank to 8 seeds per square metre in 2010.
• A selective post emergent herbicide or an early hay cut were the most effective strategies for reducing the wild oat seedbank.

The trial determined that Tigrex, Paragon, Glean, Affinity + MCPA500, Eclipse + MCPA LVE , and Jaguar + MCPA LVE provide good early post emergent control of radish in wheat. To ensure that no radish sets seed it is still important to follow up with a phenoxy herbicide later in the season. In this trial Jaguar + MCPA LVE had the highest wheat yield.

• Trials on Yellow Duplex Soils at 3 sites in the Southern Wimmera.
• At one site commercial chelated copper was foliar applied.
• Treatments were Nil; 75 or 150 g Cu/ha at late booting; 37.5 or 75 g Cu/ha at late tillering and; split applications of 75 g Cu/ha at late tillering plus either 75 g or 150 g Cu/ha at late booting.
• At two sites formulations of copper were compared, these treatments included Nil; copper oxychloride; copper sulphate and a commercial chelated copper. All were applied at 75 g Cu/ha at late tillering plus 150 g Cu/ha at booting. All plots were sown to wheat. Dry matter cuts were used at anthesis and maturity to estimate crop growth and yield components.
• Since copper is important in wheat for production of viable pollen the late booting treatments (applied after pollen set): resulted in only an 18% increase in grains/ear and grain yield.
• Whereas copper applied at late tillering increased grain yield by 1.55 t/ha or 93% (resulting from 60% more grains/ear and 20% more ears/m2 • Split applications did not result in higher yields.
• Both copper oxychloride and the chelated product resulted in grain yield increases between 0.94 and 1.26 t/ha but the chelated product is approximately seven times as expensive.

• Copper deficiency is common in wheat in South Australia and yield increases are common after copper is applied.
• Responses are observed on a range of sandy soils, especially siliceous and calcareous sands, sand over clay and soils containing ironstone.
• Symptoms of copper deficiency include wilting during early growth, leaf dieback after wilting, withertip (sterile ear tip and yellow/white ear tips), whiteheads, curved ears and heads pointing toward the ground, and blackening (melanism) of lower parts of leaves.

The program demonstrated that:
• At some sites where copper deficiency was historically assumed, no response to any form of copper application was observed. Copper response is likely to vary by site and season.
• Yield loss caused by copper deficiency can be devastating to wheat yield.
• Soil and tissue testing can be useful in helping to detect low levels, but are not always definitive. Copper response appears to be dependent on other complex interactions such as soil moisture, yield potential and other constraints (N fertility etc.) and thus soil/tissue tests alone are not a definitive guide to future responses.
• Foliar applications performed better than in-furrow liquids.
• Chelate and sulphate products performed equally well when applied as foliar applications.
• Timing did not appear to be critical, with a wide band of opportunity from mid-tiller to early head emergence providing similar results

Crop was sown as part of a rotational trial, examining the effects of Group B residues on the following maize crop.

• This was a large scale demonstration using Impact applied to the sowing fertilizer at the two label rates of 400m/ha and 200mL/ha. The two other areas were sown with no Impact on the fertilizer but one was sprayed with Impact at 250mL/ha at stem elongation. 
• There were no obvious signs of leaf diseases or other symptoms in the plots but the two Impact in furrow' treatments delivered economic yield benefits. The previous two crops grown in the area were wheat, which may mean Take-all was a factor. 

• Crop establishment was not improved by on-row seeding or by increasing seeding rate in 2016.
• Higher seeding rate increased early dry matter but this effect declined during the growing season.
• In 2016 row placement or seeding rate did not affect grain yield or grain quality.
• Sowing on-row may be an advantage on non-wetting soils with low moisture at seeding.

• Deeper sowing at 3-4 cm achieved better early dry matter and increased grain yield in a later sowing.
• Frost damage may have lowered yield with early sowing, but inter-row placement at TOS1 had the highest yield.
• TOS 3 placement in row achieved better early plant growth and higher grain yield.
• Later sowing reduced brome grass numbers, and the size of the panicles, so it substantially lowered returns to the seed bank.

2005 was not an easy year – it started off brilliantly with very good summer rains (1 in 30 year event) in the southern and central Mallee. The Wimmera did get some rain but nothing like the Mallee. Then it stopped raining until the second week in June - there were dire predictions in the media about the season, some learned scientists were even arguing that cropping in our area was not sustainable! Many people took heed from the negative predictions regarding the season and did not sow much crop dry. Sowing started in earnest in the middle of June and by mid July most of the planned cropping area was sown.

• Trifluralin use resulted in significant crop damage at this site.
• Crusader can cause early crop damage, and the label does warn about crop yellowing, but in general the crop with 'grow out' of this damage in a matter of weeks.

• Wheat sown after break crops produced up to 1 t/ha more than wheat after wheat
• The greatest benefit of the break crop was produced at the earliest sowing
• Safflower produced the break crop effect but produced low wheat yields, small grain but high protein due to drying out the soil profile.

• Glyphosate at either 1.0 or 1.5L/ha applied at the flowering stage of ryegrass was very effective in reducing the viability of seed set.
• Herbicides applied to barley at the soft or firm dough stage of grain fill did not reduce individual grain weight, grain viability or early plant vigour.

• Crop topping provides an excellent strategy to control escapee or resistant weeds in field pea
  crops.
• Yield can be severely penalised if crop topping occurs too early.
• Correct variety choice and careful timing of crop topping is essential
• Varieties should be selected to achieve maximum yield simultaneously with maximum weed
  control.
• Ontime spraying achieved excellent weed control as annual ryegrass and wild oats were at
  the flowering stage.

• Crop-topping wheat with glyphosate can result in yield loss and grain size reduction if done too early.
• Later crop-topping timings can produce grain quality and yield similar to untreated grain.

• The dry and hot November in 2009 led to early senescence of pulse varieties and reduced
  grain yields in later maturing varieties. Many responses to the crop-topping treatments may
  have been masked by this rapid senescence eg Almaz and GenesisTM114 chickpeas.
• Some surprising results were observed in 2009, which may be due to either genetic
  responses or responses to rapid finish to the season eg forage pea grain weights.
• Field peas and Faba beans generally showed no yield loss at the recommended timing for
  crop-topping of ryegrass in 2009. Lentils and chickpeas showed significantly higher yield
  losses from crop-topping, averaging 15 and 21% yield losses respectively at this timing.
• The large biomass, mid-late maturing lentil Boomer also showed a yield loss when croptopped later than recommended for ryegrass control. These results indicate poor suitability of some lines to this agronomic practice.
• Early maturing lentil and chickpea lines showed yield losses from this practice at the
  recommended timing. This demonstrates the difficulty in employing this weed control
  technique in these crop types.
• The early crop topping treatment reduced grain yields of most pulse varieties. Field peas
  OZP0602 and Yarrum at Turretfield, and the Faba bean AFO3001 showed no difference in
  grain yield at the early cop-top timing and the nil, indicating good suitability to this practice.

• Dry and hot spring conditions reduced grain yields and led to early senescence of pulse
  varieties in 2008 particularly in late flowering and/or maturing types. Many of the grain
  yield reductions expected at the mid and late crop topping timings were ‘masked’ due to
  premature senescence in many varieties brought on by these dry spring conditions.
• The early crop topping treatment reduced grain yields of field peas, lentils and chickpeas
  compared with the nil treatment, however there were field pea and lentil lines identified
  which did not incur a yield loss at this timing, indicating suitability to this agronomic
  practice.
• Some lines in all crops were found to incur yield loss and grain weight reductions at the
  appropriate timing for crop topping indicating poor suitability to this agronomic practice.
  jb66 Page 75 30/04/2009
• Not all early flowering and maturing lines were able to be safely crop topped in the 2008
  experiments nor did all late lines always incur a yield loss. Further evaluation is required to
  confirm findings in a year where varieties are not prematurely senesced by drought
  conditions.
• Detailed grain quality measurements (seed size distribution, colour, hydration percentage)
  are currently occurring on some treatments and varieties to assess the effects of crop topping and desiccation on seed quality.

• Early maturing desi chickpea varieties incurred the least yield loss at the recommended timing for crop-topping. Later varieties and kabuli types showed significant yield loss at the recommended timing and three later kabuli varieties showed yield loss at the late timing.

• The wet season end in 2010 meant that all varieties showed reduced yield and grain weight
  from the early crop-top timing, regardless of maturity.
• At the recommended crop-top timing yield of the later maturing lines Parafield, Yarrum and
  Glenroy was significantly affected, while some later maturing lines were not. This may have been a result of a moderate powdery mildew infection at this site, which sped up maturity of
  sensitive lines. Yarrum, which has mid maturity and is powdery mildew resistant, would not
  otherwise have been expected to show this yield penalty at this timing as shown by 2009
  results.
•  Further work is required to validate these results.

• Yield losses from Early crop-topping generally followed cultivar maturity, with latest maturities
  showing highest losses. Parafield and Alma were the only varieties to show yield loss at the
  Recommended timing, supporting previous findings that these later maturing varieties are not as well suited to crop-topping as recent releases PBA Twilight, PBA Gunyah and PBA Oura. Kaspa and Yarrum continue to show a variable result across seasons at this timing.

• The wet and late finish to the 2010 season meant that early crop-topping was very detrimental to yield of all lentil varieties
• Later maturing lentil varieties also showed a yield penalty from crop-topping at the recommended timing (ryegrass milky dough stage).
• CIPAL0501 was the most sensitive variety to crop-topping, showing a reduction in yield from crop-topping at all three timings. This variety also has the latest maturity in this trial.
• The early crop topping treatment reduced grain yields of most pulse varieties, while the late
  crop-top timing had no effect on grain weight.

• There was limited varietal response from crop-topping in 2011. This may be due to below  average rainfall during late October and early November, the rapid finish on a shallow soil and the relatively late sowing date, suppressing some yield potential of untreated plots.

• There was no significant difference between sowing systems or level of nutrition on grain yield but higher grain yield at the higher nitrogen rate.
• Levels of brome grass were higher under the early sowing no-till plots and annual ryegrass was lower in the disc system.

• There was no significant difference between sowing systems or level of nutrition on grain yield.
• Levels of brome grass were higher under the early sowing no-till plots and annual ryegrass was lower in the disc system.
• There is very little difference in long term gross margin between seeding system or level of nutrition.

• The disc and the early sown no-till tillage systems produced the highest grain yields, 1.41t/ha and 1.36t/ha respectively.
• The early sown no-till system had the lowest protein and the highest screenings.
• The disc tillage treatment had the least available soil nitrogen in autumn.

• All the legumes sown - peas, lupins, sub clover and faba beans - were equal in terms of their nitrogen-fixing capabilities, reflecting the importance of having well nodulated legumes.
• The average amount of N fixed by the legumes was calculated at approx. 86kg/ha.
• In year 2, this residual N gave rise to a approx. 1 t/ha canola yield advantage.
• In yera 3, no differences in residual nitrogen from legumes were measured.
• Linseed extracted more moisture, from a greater depth, than the faba beans in the same year and all subsequent crops - canola and oats.
• The linseed was able to dry the soil profile in a decile 10 year (812mm rainfall). This is a potential solution for farmers wanting to dry out their soil profile.
• Two years after growing linseed, soil moisture levels were even.

• Dry and hot spring conditions led to poor pod set and early senescence of faba bean varieties in 2007. Grain yields of earlier maturing varieties were higher than those of later maturing types.
• There was no significant interaction between crop topping timing treatment and variety
  performance for grain yield as late varieties were lower yielding in all treatments, including
  the nil treatment due to the dry seasonal conditions.
• Generally earlier maturing varieties incurred lower levels of grain yield loss than later
  maturing varieties when crop topped at the appropriate stage for effective ryegrass control.
  However this difference was not significant in the 2007 trial.
• The concept trial methodology for evaluating relative yield loss due to various crop timings
  was found to be sound and will be repeated in 2008, although trial layout changes will be
  made to improve spraying logistics. A very early timing treatment will be added to assess
  the extremes of yield loss potential in all varieties and detailed flowering and maturity
  scores will be taken. Field pea, lentil and chickpea varieties will also be evaluated.

Key findings:

• Nitrogen (N) decision making requires a good understanding of background soil and plant science, and soil test interpretation.
• Training for new agronomists needs to be a priority issue.
• Senior NSW agronomists identified crop yield expectation as guided by soil moisture at sowing (or at the time of N decision making) as the most important determinant of N fertiliser requirement.
• Further research is needed to increase the understanding of how management practices affect potentially large gaseous N losses. 
• Changing from legume pasture-crop sequences to continuous cropping in many central and southern areas of New South Wales is posing new questions for managing N supply. The absence of N-fixation by pasture legumes is seen as a substantial loss of N-buffering capacity.
• Despite most advisers choosing soil testing as a key approach for determining N fertiliser required, many of their clients had a lower confidence in soil testing, citing ‘high perceived variability in soil nitrate results in the lead up to sowing’.
• Conclusions and Recommendations Senior advisers highlighted the importance of quality training in N decision-making, understanding the background soil and plant science involved, and soil test interpretation for the next generation of agronomists, with training courses including representation from highly experienced local agronomists.
• The understanding of gaseous N losses requires further research, development and extension to the grains industry. Recent field research in the north was limited in scope and produced challenging outcomes that can potentially lead to large practice changes in when and how N fertiliser is applied. Further research and development work is warranted to answer more of the practical questions growers and advisers are asking in regards to losses associated with various alternative practices.

• The northern results on N loss pathways are less relevant to advisers in the central and southern regions where N application timing, soil type and climatic differences are generally quite different from the dominant medium-heavy clays of the north. New N loss research is recommended for the lighter textured soils in regards to the potential for N volatilization losses from surface N application of various products. Economic outcomes from the various strategies being practiced are also needed. Nitrogen loss research should focus less on expensive slow-release products and more on optimising results from urea, the cheapest N source.

• Research into better soil water measurement was seen as a priority area, especially given the importance all advisers place on knowing this when making expensive N-fertiliser decisions for a coming cropping season. Zonal management within paddocks is not possible with single site characterisations, so atypical areas of paddocks are over or under-fertilised.

• The very early application of N fertiliser ahead of a winter cropping season is well established, but what is not known is how well the subsoil N may be protected or at risk from denitrification in flooding events. Also, better knowledge on specific N use within the profile during the cropping season will help growers to know when late-applied N is likely to be inaccessible to crop use.

• Nitrogen mineralisation was highlighted by agronomists from all three regions as an area for greater understanding with regards to the differences caused by climatic conditions, especially rainfall. They also require better understanding of the N produced from both native organic matter and recent legume pasture residues.

• There are a number of good decision support tools available currently, with several advisers suggesting that combining the best points of each into one package, even one available as an app, would be highly useful, particularly one with good grower-friendly reports.

• Many farmers have low confidence in soil testing.  This may be related to a range of factors from poor sampling strategies, to poor sample handling, to poor service from laboratory analysts, to insufficient sample numbers or poor interpretation of the results. It is seen as an expensive option for many, with some advisers looking for quicker and cheaper means of estimating soil mineral N.

• Variety-specific N management packages were seen by some senior advisers as key areas for continued research funding, as results from some new varieties have been quite different in terms of N uptake and protein outcomes.

• The trial area was seeded in June 2015 to wheat by Peter Negus, while he was seeding the surrounding paddock.  Unfortunately, the seeder ran out of seed as the trial was being sown.  The result was that there were large unseeded strips running through the trial. 
• Rainfall at the site was very poor in September and October 2015; approximately 70% below average for that period.  As a result, cereal crops on soils with low water holding capacity were badly affected, with yields well below average.
• Analysis of the harvest results (excluding plots affected at seeding) showed no significant differences, leading us to conclude that either (a) the tillage and lime treatment effects have ‘worn out’ at the site, or that (b) poor rainfall in September and October severely reduced yields, obscuring any other effects.  We believe that (b) is more likely.
• This trial will be sown to lupins in 2016.

The pH results from this trial show some interesting trends. 

The treatments with greater disturbance at depth (spade, deep rip + spade, mouldboard) tend to decrease surface pH.  This is of concern if the ‘new’ topsoil pH is acidic enough to inhibit root development. 

The treatments with greater disturbance at depth (spade, deep rip + spade, mouldboard) tend to increase midsoil pH most rapidly.  This is the effect hoped for.  The differences between treatments are generally not significant, but more intensive sampling may tease out differences.

The treatments with greater disturbance at depth (spade, deep rip + spade, mouldboard) tend to increase subsoil pH most rapidly.  This is the effect hoped for.  The differences between treatments are generally not significant, but more intensive sampling may tease out differences.

Deep cultivation strips on growers’ properties did not show much in the way of early responses and so did not excite much grower interest as a direct diagnostic of the hardpan conditions in their paddocks. However, at responsive sites, there was a lot of grower interest to the level where it might be worth funding another year of this direct diagnostic approach in the hope that early season conditions are conducive to major nitrogen growth responses.

June 13th sown Gairdner produced yields in the range of 4.86 – 5.69 t/ha following canola stubble. With high soil nitrogen reserves (203 kg/ha N, 0‐90cm) recorded at sowing, there was a small but significant response to applied nitrogen (0.21 t/ha at 50 kg/ha N & 0.23 t/ha at 100 kg/ha N). There was a significant advantage to nitrogen timed during stem elongation (GS31‐33) over nitrogen applied in the seedbed.

Late sown Mitre (July 4) produced yields in the range of 0.6 – 2.16 t/ha following Canola stubble. With soil nitrogen reserves of approximately 30kg/ha N (0-10cm) recorded pre sowing, applied nitrogen was detrimental in this trial, with 50 kg/ha N reducing yield by 0.09t/ha and 100kg/ha N reducing yield by 0.23 t/ha. These figures disguise more detrimental yield reductions with seedbed nitrogen applications and no effect from stem elongation timings applied at GS31-39.

Late sown Mitre (July 4) produced yields in the range of 0.6 – 2.16 t/ha following Canola stubble. With soil nitrogen reserves of approximately 30kg/ha N (0-10cm) recorded pre sowing, applied nitrogen was detrimental in this trial, with 50 kg/ha N reducing yield by 0.09t/ha and 100kg/ha N reducing yield by 0.23 t/ha. These figures disguise more detrimental yield reductions with seedbed nitrogen applications and no effect from stem elongation timings applied at GS31-39.

• In 2019 the IMI system had the lowest barley grass plant numbers.
• The Cultural Control strategy did not achieve the desired outcome of having a more even seed spread and increased competition in the inter row for barley grass weed control.
• The medic pasture produced low dry matter compared to the cereal systems, had the highest barley grass population and the lowest competitive ability with the barley grass.
• The loss of Group A herbicides to control barley grass within local pasture systems has the potential to change rotations and decrease farm profitability.

• In 2019 the IMI system had the lowest barley grass plant numbers.
• The Cultural Control strategy did not achieve the desired outcome of having a more even seed spread and increased competition in interrow row for barley grass weed control.
• The medic pasture produced low dry matter compared to the cereal systems, had the highest barley grass population, and the lowest competitive ability with the barley grass. 
• The loss of Group A herbicides to control barley grass within local pasture systems has the potential to change rotations and decrease farm profitability.

 

A demonstration to showcase options for managing water repellent soils was established in 2017. Mace wheat was sown into sand over gravel (below 20cm) on 24 May following 209mm summer rain, with no rain in April and 14mm in May.

• One-way plough reduced subsoil compaction to 30cm depth and improved soil wettability, crop establishment and yield.
• Deep ripping reduced compaction to 30 cm depth, improved crop establishment and yield, but not soil wettability.
• Knife point sowing established and yielded better than the splitter boot when sowing on deep ripped and one-way ploughed plots.

• During the season, plant growth was measured using a Greenseeker to measure Normalised Vegetation Differential Index (NDVI) at early tillering (growth stage GS14), end of tillering (GS30), and at the end of stem elongation (GS40).
• This data has not been presented in this report.

• Adequate control of weeds and sufficient plant densities resulted in a clean, competitive crop at the Carnamah site. Canola remains a high earning crop that commonly forms part of a crop rotation in many farming enterprises. Robust agronomy packages and prices of the legume types demonstrated by this project, means crops such as field peas and lentils have potential suitability in the Carnamah region.
• The need to harvest chickpeas early to match the logistics of harvest of the trial compromised the results for the chickpea treatments. Use of established management practices for the harvesting of chickpeas is required to reduce the incidence of yield loss at harvest time.
• The ranking of each species on profitability should be viewed in light of the highly variable price of pulses from year to year.
   

• The early maturity of Quilinock and Belara allowed these avrieties to avoid significant crop loss from the first gramozone croptopping treatment.
• Mandelup was affected by the first gramozone treatment but not as much as Tanul and Kalya.
• The competitive yield preformance of Mandelup was also determined.

 There was a visual response to P applied at sowing which resulted in additional yield at harvest. Responses were obtained to up to 10 kg/ha of P. The added net income was calculated as $44 /ha or a $3 return for every $1 spent. There was no visual response to applying N. This may have been a result of the dry pring and the time of application. There was no response to N at harvest.   The co-operator was please that he noted a visual response to applying P that resulted in higher yields. The ack of N response was probably due to the dry weather in early October.

• Early and on time desiccation resulted in large yield losses.
• Early and on time desiccation resulted in large reductions in seed size, but not to the same
  degree as yield.
• What were the reasons (other than reduced seed size) that contributed to these yield
  losses? Was ‘pinched’ seed lost through the header at harvest?
• Yield losses were bigger in the later flowering variety Kaspa.
• Need to more closely fine-tune growth stages with physiological maturity to pick the “on
  time” desiccation spray.
• Oura and Pearl were early and the pick of varieties suited to crop-topping & desiccation.

The Winchelsea site, sown in late April to Amarok red wheat, had yield variations across the site, with highest yielding plots reaching 3t/ha.  These plots although nearest the shelter belts, were the stubble incorporated treatments.  In comparison, where incorporation did take place with either the addition of chook manure or biological applications, there was a reduced yield of up to 0.6t/ha.  Burning at this site yielded 2.33t/ha, being the lowest output for this site

• Zinc deficiency caused production losses in cereals of up to 25% and in medic of up to 300% in biomass.
• Critical level for zinc deficiency in wheat was established as 18 mg/kg in YEBs at late tillering.
• Zinc deficiency in crops can be corrected with foliar sprays, zinc coated fertilisers or zinc applied to the soil and thoroughly incorporated by tillage. Fertilisers which are a mix of NP granules and zinc granules are poorly effective.
• Zinc applied to the soil will provide residual benefits for 3-10 years, the longer persistence in sandier mallee soils.
• 70% of cereal crops in the SA mallee were zinc deficient in the early 1990s.
• An application of 2 kg zinc/ha to the soil (as an incorporated soil spray or zinc coated fertiliser) will correct zinc deficiency in broadacre crops and pastures.

• Although soil measures of zinc availability indicated sufficiency, zinc deficiency was severe in the untreated plots.
• Yield responses to foliar zinc of up to 86% were observed in sensitive cultivars.
• Some cultivars were not responsive to applied zinc and did not show any symptoms of zinc deficiency.
• Appropriate early treatment with foliar sprays eliminates zinc deficiency.
• Where soils are shown to be zinc deficient soil applications may be warranted but interactions with phosphorus need to be understood.

• Time of sowing is more important than seeding system.
• Depth control on disc seeding systems can affect crop establishment.
• In this trial the knife-point press wheel seeding system out yielded the single disc seeding system.

• Early break to the season triggers a very early canola sowing time (22 March) in a time of sowing trial at Minnipa.
• Disappointing yields and no stand out varieties in time of sowing 1 (TOS1) at Minnipa missing the full potential for early sowing due to shattering and mice damage.
• Exceptional yields in TOS2 Clearfield trial at Minnipa where Hyola 571 CL, Pioneer 44Y84 CL and Pioneer 43C80 CL all exceeded 2.5 t/ha.
• ATR Stingray, CB Junee HT and ATR Snapper are the highest yielding TOS2 TT lines at Minnipa.
• Hybrids Hyola 571 CL, Pioneer 45Y82 CL and Pioneer 44Y84 CL shine in the Clearfield trial at Witera yielding above 2 t/ha.
• ATR Cobbler, ATR Stingray and Tanami are the best performing TT lines at Witera.
• Oil content in canola is above 42% across all trials.

• Fluid fertilisers performed better (increased early growth and grain yield) with the addition of low rates of micronutrients.
• Foliar micronutrients were more economic than granular.

• Winter habit canola was successfully sown in spring 2011, grazed over summer and harvested for grain in 2012.
• Grazing over summer increased grain yield compared to no grazing. Ungrazed yield was 1.9 t/ha, grazed was 2.7 t/ha. Taurus sown at the conventional time (April) yielded 2.3t/ha. 
• Number of grazings had a small effect on yield. Grazing twice produced the best result, yielding 0.1t/ha more than grazing once and 0.2t/ha more than grazing three times. Although there was a yield penalty by grazing 3 times compared to two times, the third grazing supplied an additional 1t/ha of high quality feed at the beginning of May.
• Heavy grazing reduced yield compared to light grazing irrespective of the number of times it was grazed. However the reduction in yield was small and the heavy grazing produced 4t/ha of feed compared to 1.4 t/ha when lightly grazed. 
• Applying nitrogen over summer has no yield benefits except for multiple (3) heavy grazings. In this case yield went from 2.0 t/ha to 2.7 t/ha

• Canola yield was increased and oil % marginally decreased with increasing N rate applied.
• The highest yield (4.2 t/ha) was achieved at the highest N rate (160 kgN/ha).
• With adequate starting soil N (67 kgN/ha) and good spring rain, N application timing made little difference.
• 30% N fertiliser recovery in grain remains a good ‘rule of thumb’ for canola N budgeting.
• Easy N® application shows promise for topping up N at early flower.
   

• Pasture species were out competed when sown with Fathom barley.
• Even when pasture species were sown as monocultures weed competition reduced biomass production in winter and summer.
• Fathom barley produced the most dry matter and the vetches and peas performed comparatively well.

• Dry sowing before the break limits the possibility of broad spectrum herbicide control of early germinating weeds.
• Annual ryegrass is very competitive if it emerges before or with the crop. Delaying sowing until the first flush of weed seedlings have emerged to allow an effective knockdown with a broad spectrum herbicide is pivotal when sowing into paddocks with a high ryegrass seed bank
• The seed rate and consequently the plant density will most likely not create conditions where the rapid early growth of Revenue will out compete the germinating ryegrass. In this case, the density of plants does not play a significant role in the outcome of weed suppression.
• Application of IBS herbicides (Sakura, Avadex Xtra) lose weed kill effectiveness with extended periods of hot weather and minimal rainfall.

 

• Annual medics are widely grown on neutral to alkaline soils that commonly contain high levels of boron in the subsoil that reduce plant growth.
• Boron tolerant barrel, strand and disc medic cultivars exist, but all spineless burr medic cultivars are intolerant of high boron levels.
• A cohort of boron tolerant spineless burr medics have been developed and entered field evaluation trials at Minnipa and Roseworthy in 2019.

• Pasture legumes sown in 2018 were allowed to regenerate in 2019 and were grazed with ewe hoggets.
• Sheep live-weight increased on average by 13.8 kg (+26%, ~180 g/day) and was similar for all legume treatments, but differences between the sown legumes may have been masked by volunteer pasture species in the plots.
• Sown legume intake ranged from 401 kg/ha (Trigonella balansae) to 1461 kg/ha (Harbinger medic). Sheep showed some grazing preference for medic over trigonella. 
• The site will be sown with wheat in 2020. Crop growth, grain yield and quality will be measured. Stubbles will be grazed. It will return to pasture in 2021.

• This is a component of a new five year Rural Research and Development for Profit funded project supported by GRDC, MLA and AWI; and involving Murdoch University, CSIRO, SARDI, Department of Primary Industries and Regional Development; Charles Sturt University and grower groups.
• This trial aims to assess a diverse range of annual pasture legumes in order to determine whether there are more productive and persistent options for the drier areas (<400 mm) of the mixed farming zone of southern Australia.
• Several new legume species established well under very difficult conditions, but in general were not as productive as the medics or vetch. 
• In the 2018 growing season, Caliph barrel medic was the best adapted pasture legume species to the conditions at Minnipa.
• Astragalus was the best adapted alternative legume species, although it was poorly nodulated.
• Zulu arrowleaf clover also performed well, however its peak dry matter production and flowering time may be too late for SA conditions.

• This is a component of a new five year Rural Research and Development for Profit funded project supported by GRDC, MLA and AWI; and involving Murdoch University, CSIRO, SARDI, Department of Primary Industries and Regional Development; Charles Sturt University and grower groups.
• This trial aims to assess a diverse range of annual pasture legumes in order to determine whether there are more productive and persistent options for the drier areas (<400 mm) of the mixed farming zone of southern Australia.
• Annual medics continue to be the best pasture option for neutral/alkaline soils on the upper Eyre Peninsula. Common vetch is an alternative option where a sown legume ley of one year duration is preferred.
• Building up a seed bank is critical to the longer term performance of the pasture. The aim in the pasture establishment year should be to maximise seed set.
• Levels of hard seed affect regeneration. Legumes with high hard seed levels should be cropped in the year following establishment.

• Novel legume species and genotypes have the potential to reduce feed gaps and provide other farming systems and livestock benefits in low to medium rainfall regions of southern Australia.
• The five-year large scale grazing systems trial established at Minnipa in 2018 is the main livestock field site for the national Dryland Legume Pasture Systems project. Five annual legume species are being tested.
• The priority for this trial in 2018 was to optimise seed set given the poor seasonal conditions, and therefore no grazing was undertaken in the establishment year, but instead will commence with sufficient pasture growth in 2019 to determine the best legume option for livestock production. 

This is a component of a five year Rural Research and Development for Profit funded project supported by GRDC, MLA and AWI;
and involving Murdoch University, CSIRO, SARDI, Department of Primary Industries and Regional Development; Charles Sturt University and grower groups.
• This trial aims to assess a diverse range of annual pasture legumes in order to determine whether there are more productive and
persistent options for the drier areas (<400 mm) of the mixed farming zone of southern Australia.
• The annual medics were the most productive pasture legume producing > 2 t/ha DM and setting > 500 kg/ha of seed. A new Tetraploid Barrel medic was the most productive.
• Astragalus was the most promising alternative legume and warrants further evaluation.

• 2007 results showed two varieties experienced statistically significant yield penalty from mowing when medium maturing varieties were mowed at growth stage 30 (given appropriate crop management).
• Early sowing thought to be very critical to minimizing yield penalty from grazing - to be researched .
• Crop management will be different for both graze/grain versus pure grain crops - to be researched.
• Grazing crops gives pastures a chance to establish and grow at optimal growth rates during winter.
• Sheep can be used to selectively graze weeds - to be researched.

• Yield premium for Long season wheat varieties April sown vs May sown was 920 Kg/Ha
• SCF dual purpose/dual use long season HRZ wheat production package is being upgraded with each year’s research and case studies (2016-2019)
• Product testing for flour blend characteristics and feed qualities such as metabolisable energy in progress
• CBH trial offer for dual purpose/dual use long season wheat

Wheat grain yields following grazing were surprisingly high and it would appear grazing was not detrimental to grain yield. Reduced dry matter from grazing may have resulted in less water useage early in spring with more then being available during grain fill. Of the wheat varieties, the grain yield of the line 1SR594-34 was particularly high. Dry matter production (from the one cut taken) was significantly lower for the wheat varieties but given the current high grain price dual purpose wheat is an attractive option. 
 

• Grazing once early in the season did not affect grain yield.
• Grain yields were reduced when varieties were grazed late in the season.
• Oats and barley showed better early vigour than the wheat varieties.