• Early sowing exacerbated phenological differences between the varieties.
• The spread of days to reach 50% flowering within each time of sowing (TOS) varied by 35, 26 and 14 days in TOS 1, TOS 2 and TOS 3 respectively.
• The highest yield was acheived by Nuseed GT-50 (3.9 t/ha) sown on 1 May.
• Hyola 600RR was the highest yielding variety when averaged across all sowing dates.
• The sowing time had a neglible impact on grain yield. 
• The biomass at 50% flowering was greatest in TOS 2 (9.92 t/ha) followed by TOS 1 (7.93 t/ha) and TOS 3 (9.23 t/ha).
• There was strong correlation between biomass at maturity and grain yield, i.e. a higher biomass produced a higher yield.  

• Frost and terminal drought were key determining factors on barley grain yield and development at Condobolin in 2017.
• Selecting sowing date and varietal phenology maximised grain yield by timing flowering for the first week of September at Condobolin.
• Grain plumpness, as indicated by screenings and retention, can be adversely affected by late sowing dates in the absence of spring rainfall.

• Slower maturing varieties had the highest yields in 2016, uncharacteristic of long-term yield trends in central west NSW, where weather conditions typically favour shorter-season varieties.
• While anthesis date is a important contributor to yield, high rainfall and a long grain filling period diluted this association and was confounded by lodging, secondary tillering and waterlogging events.
• Highest yields were attained from the second sowing date (mid May), while late sowing dates suffered yield penalties due to poor plant establishment from waterlogging.  

Key findings

 Sowing time had a huge effect on grain yield.

 Delaying sowing time reduced grain yield, TOS 1 yielded 4.84 t/ha and TOS 2 yielded 3.55 t/ha.

 Suntop was the highest yielding variety, 4.47 t/ha.

 Lancer was the lowest yielding variety, 3.73 t/ha.

 Given profitability and return on investment 40 kg N/ha at sowing was the ideal rate of nitrogenSowing time had a huge effect on grain yield.

Delaying sowing time reduced grain yield in all varieties across all nitrogen treatments.The effect of nitrogen varied between the two sowing times. The ideal target rate of nitrogen, given profitability and return on investment was 40 kg N/ha.

Key findings:

• Sowing time had a huge effect on yield.
• Delaying sowing time reduced grain yield in all varieties across all nitrogen treatments. 
• Given profitability and return on investment 40 kg N/ha at sowing was the ideal rate of nitrogen.

• The combination of extra stored water (20mm) and early sowing (17 April) resulted in the highest grain yield in this experiment.
• Early sowing without extra stored water gave a higher yield than late sowing (4 May), regardless of teh irrigation treatment at the later sowing date.
• The extra grain yield from early sowing and irrigation was due to increased biomass accumulation and imprved harvest index.
• Oil concentration was low overall, but was higher from the early sowing (33.6%) than th elater sowing (30.5%).

• LBP10 - 0018 was the highest yielding variety sown on the 30th April (2.09 t/ha)
• Emu Rock was the highest yeilding variety sown on 22 May (1.72 t/ha) and 11 June (0.89 t/ha)
• Emu rock was the highest yielding variety (1.49 t/ha) when averaged accross all sowing times.
• Dry conditions during September and October contributed to the lower average yields in the 22 May  and 11 June sowing times

A field trial was undertaken at Mallala in 2019 to investigate combinations of wheat sowing time, seed rate and herbicide treatments to control brome grass. The average seedbank of brome grass at this site was 2877 ± 406 seeds/m2. The two week delay in sowing reduced average in-crop brome density from 567 plants/m2 to 352 plants/m2 (38%). Even though the reduction in brome density at Mallala was significant, it was a much lower reduction than that observed in the trial at Riverton (82% reduction). This difference in brome grass density with delayed sowing at these two sites highlights the large differences in seed dormancy between the populations of this weed species. Brome grass panicle density was significantly affected by wheat seed rate (P=0.039), and herbicide treatment (P<0.001) but not by the time of sowing (P=0.152). Increasing seed rate of wheat suppressed brome grass growth and reduced its panicle density. As wheat density increased from 100 seeds/m2 (low) to the highest seed rate (200 seeds/m2 – high) brome panicle density was reduced by 39%. These results support previous findings that higher crop density can be an important part of an integrated weed management program. Wheat grain yield increased consistently with the increase in seed rate or crop density. This trend correlates well with the improved suppression of brome grass panicle density observed in the trial. Not only did higher wheat density achieve superior weed suppression, it also provided a significant increase in grain yield. Herbicide treatments also had a highly significant effect on brome grass panicle density. However, there was no interaction herbicides and TOS or seed rate. This indicates that herbicides performed similarly in both times of sowing and the three seed rates. Sakura + Avadex significantly reduced panicle density as compared to Treflan + Avadex and Intercept (Clearfield technology) was used after pre-emergent Treflan + Avadex, it prevented brome plants from producing panicles (3 panicles/m2). Herbicide treatments had a large and significant effect on grain yield of wheat at Mallala (Figure 5). This is not surprising considering the high weed density present at the site and high competitive ability of brome grass. The treatment of Treflan + Avadex produced only 1.11 t/ha, which was significantly lower than the more expensive pre-emergent herbicide mixture of Sakura + Avadex (1.81 t/ha). However, when Intercept post-emergence herbicide was used, wheat yield increased further to 2.63 t/ha. In this trial, integration of Clearfield technology with pre-emergent herbicides not only prevented brome grass seed set as shown but the panicle density, it also delivered the highest grain yields.

A field trial was undertaken at Riverton in 2019 to investigate combinations of wheat sowing time, seed rate and herbicide treatments to control brome grass. The average seedbank of brome grass at the site was 1863 ± 303 seeds/m2. Brome grass at this site was effectively controlled (>80%) by delaying sowing by 2 weeks, with treatment effects from herbicide and wheat seed rate treatment only being significant in the early sown plots, where brome grass density was high. These results clearly indicate that brome grass population present at this site has very low seed dormancy and germinates readily after the season opening rains and can be effectively controlled with a knockdown herbicide. Wheat grain yield results reflected the level of brome grass control with herbicide and wheat seed rate treatments improving yields significantly as brome suppression improved. These treatments did not have a significant effect on yield when sowing was delayed because brome was effectively controlled by the knockdown herbicides. In the early sown crop when brome grass was controlled effectively with Intercept®, the 2 week delay in sowing caused a 9% reduction in wheat yield.

• There were large weed control benefits of delayed sowing of barley at Minnipa. However, when a highly effective pre-emergent herbicide was applied the benefit of delayed sowing was negligible.
• In barley a three week delay in sowing time did not significantly reduce grain yield as it did in the previous year in wheat. Lower yield penalty in barley from delayed sowing may be related to its earlier maturity and more competitive nature compared to wheat.

 

A field trial was undertaken at Minnipa in 2019 to investigate combinations of barley sowing time, seed rate and herbicide treatments to control annual ryegrass. The average seedbank of annual ryegrass (ARG) at the site was 4168 ± 411 seeds/m2. ARG plant density was significantly influenced by the time of sowing (P<0.001), herbicide treatment (P<0.001) and the interaction between the time of sowing and herbicide (P<0.001). There was a large impact of the 3 week delay in seeding barley on ARG plant density. This was particularly evident in the untreated control in which ARG density decreased from 676 plants/m2 in TOS 1 to 379 plants/m2 in TOS 2. This large reduction in ARG density due to delayed sowing is most likely related to rainfall events in early May, which would have caused weed emergence. Pre-emergence herbicides had higher efficacy in TOS 2 where the density of ARG plants had been reduced by the delay in seeding. This trend held through the season in the untreated control in which ARG spike density decreased from 306 spikes/m2 in TOS 1 to 199 spikes/m2 in TOS 2. In the trifluralin treatment, ARG produced 5078 seeds/m2 in TOS 2 as compared to 9192 seeds/m2 in TOS 1, a 45% reduction in ARG seed production. Unlike wheat in 2018, barley grain yield at Minnipa was not significantly influenced by the time of sowing (P=0.644). However, seed rate (P<0.001), herbicide treatment (P<0.001) and had a significant effect on barley grain yield. As stated earlier, there were large benefits of delayed sowing on weed control. In barley a three week delay did not significantly reduce grain yield as it had in the previous year in wheat. Lower yield penalty in barley from delayed sowing may be related to its earlier maturity than wheat.

Barley grain yield as significantly influenced by the time of sowing (P=0.025), seed rate (P<0.001) and the herbicide treatment (P<0.001). The delay of 4 weeks between the two sowing dates caused 22% (0.69 t/ha) reduction in grain yield or 25 kg/ha/day. Averaged over the two sowing dates and three seed rates, Boxer Gold treatment (2.996 t/ha) produced significantly greater barley grain yield than Treflan (2.634 t/ha) and the control (2.648 t/ha). Barley sown early (TOS 1) at high seed rate and sprayed with Boxer Gold produced 3.6 t/ha grain yield as compared to later sown crop (TOS 2) at low seed rate but treated with the same herbicide which produced 2.4 t/ha.

General application of Sakura + Avadex over the whole trial site provided good control of ARG. As a result, follow-up application of Boxer Gold @ 1.5 L/ha or 2 L/ha at GS 11 (1-leaf stage) did not significantly reduce ARG plant density.  Post-emergence application of Boxer Gold at 1.5 or 2 L/ha after pre-emergence Sakura + Avadex extended the period of weed control, which reduced spike density of ARG (P=0.02). At both sowing times, increase in wheat plant density from 100 to 200 plants/m2 reduced ARG spike density by 44%. Delayed sowing at this site reduced the competitive ability of wheat against ARG. Averaged across the seed rates and herbicide treatments, ARG produced 234 spikes/m2 in TOS 2 as compared to 75 spikes/m2 in TOS 1 (68% reduction in TOS 1). Additional post-emergence application of Boxer Gold significantly increased wheat grain yield (P=0.008) compared to the baseline treatment of Sakura + Avadex. Wheat yield increased by 9% or 0.4 t/ha with the additional post-emergence treatment of Boxer Gold as compared to Sakura + Avadex treatment alone. Wheat grain yield was also significantly affected by wheat seed rate (P<0.001). Wheat grain yield increased from 4.6 t/ha at the density of 100 plants/m2 to the maximum of 5.48 t/ha at the seed rate of 200 plants/m2. This yield gain of 0.9 t/ha clearly indicates that early sowing, wheat density of 200 plants/m2 and effective use of herbicides can have a large influence on the profitability of wheat in the HRZ.

Wheat grain yield at Minnipa was significantly influenced by the time of sowing (P=0.002), seed rate (P<0.001), herbicide treatment (P<0.001) and the interaction between the time of sowing and herbicide treatments (P<0.001). Averaged across the seed rates and herbicide treatments, wheat produced grain yield of 1.67 t/ha in TOS 1 as compared to 1.06 t/ha in TOS 2. There were large benefits of delayed sowing on weed control. However, these benefits came at a significant cost in wheat grain yield.

The trial site at Mallala was infested with a large seedbank of group A resistant brome grass, which made weed control in canola very difficult. Furthermore, the trial site experienced drought like conditions for most of the growing season which reduced the efficacy of atrazine. Even though the two-week delay in sowing reduced brome grass density from 927 plants/m2 in TOS 1 to 704 plants/m2 in TOS 2 (25%), this difference was not statistically significant.  However, the herbicide treatments (P=0.005) and the interaction between sowing date and herbicides (P=0.006) had a significant effect on brome grass plant density. Herbicide performance at the site was negatively affected by dry conditions and group A resistance in brome grass. As a result, even the best treatment combinations had more than 300 panicles/m2, which could lead to a large seed set in brome grass. When averaged across the sowing time, seed rate and herbicides, HyTTec Trophy produced 38% higher grain yield than Bonito. This difference in variety performance is consistent with superior crop establishment in HyTTec Trophy than Bonito. As a result of herbicide resistance in brome grass, yield increase in the Verdict treatment compared to the control (atrazine POST) was non-significant. However, use of clethodim increased yield by 61% compared to the control, which was statistically significant.

Barley plant density was significantly influenced by the time of sowing (P=0.025) and crop seed rate (P=0.002).  Averaged across the seed rates and herbicide treatments, the first time of sowing (TOS 1) had barley density of 125 plants/m2 compared to 82 plants/m2 in TOS 2, which was related to dry soil conditions after sowing in TOS 2. Brome grass plant density was significantly affected by the time of sowing (P=0.018) and the herbicide treatments (P<0.001).  The 4-week delay in sowing between TOS 1 and TOS 2, allowed greater emergence of brome grass seedlings before the sowing of the TOS 2.  Consequently, barley sown at TOS 2 had 48% lower brome grass infestation (107.9 plants/m2) than in TOS 1 (207 plants/m2). As expected, herbicide treatments had a significant (P<0.001) effect on brome grass density. When averaged across the sowing time and seed rates, the treatment of Treflan + Avadex was only moderately effective and reduced brome grass density by 36% (173 plants/m2) relative to the untreated control (271 plants/m2). In contrast, the same pre-emergent treatment (Treflan + Avadex) followed by Intervix reduced brome grass density by 90% (28 plants/m2). When averaged across seed rates and herbicide treatments, the time of sowing barley had a significant effect on its grain yield (P=0.011). TOS 1 produced 940 kg/ha greater barley grain yield than TOS 2. The post-emergence application of Intervix to the crop treated with Treflan + Avadex further increased barley grain yield by 872 kg/ha. These results are consistent with the trends in brome grass density and panicle production. The untreated control plots produced 40% lower grain yield than the Intervix treatment, which completely controlled brome grass. These results highlight the strong competitive ability of brome grass in cereals.

The average seedbank of ARG at the site was 3932 ± 270 seeds/m2. ARG plant density was significantly influenced by the time of sowing (P<0.001), herbicide treatment (P<0.001) and the interaction between the time of sowing and herbicide (P<0.001). The delay in seeding from TOS 1 to TOS 2 (16 weeks) caused a large reduction in ARG plant density. This was particularly evident in the untreated control in which ARG density decreased from 825 plants/m2 in TOS 1 to 31 plants/m2 in TOS 2 (96% reduction). This large reduction in ARG density due to delayed sowing is most likely related to an effective knockdown herbicide treatment after most ARG had emerged before TOS 2. Herbicide treatments reduced ARG plant density significantly in TOS 1, however herbicide effect on ARG plant density in TOS 2 was non-significant, possibly due to a much lower ARG density. While the delay in sowing significantly reduced ARG plant density (P<0.001), it did not significantly reduce ARG seed spikes (P=0.495). This result indicates that despite low ARG plant numbers in TOS 2, faba beans failed to compete effectively with ARG and suppress its growth. As a result, even at a relatively low density ARG was able to produce a large amount of seed for future infestations. Faba bean grain yield at Frances was significantly influenced by the time of sowing (P=0.033), seed rate (P<0.003), and herbicide treatment (P<0.001). Averaged across the seed rates and herbicide treatments, faba beans produced grain yield of 1.34 t/ha in TOS 1 as compared to 1.81 t/ha in TOS 2. Superior faba bean grain yield in TOS 2 In 2018 at Frances is most likely due to the reduction in ARG plant density.

• There was no difference in grain yield (t/ha) between the early season variety (Trojan) and the later varieties (Mace and Scepter) sown 13 days later.

• In 2016 sowing Mace and Scepter earlier on 13 May reduced grain protein by 0.3% compared to sowing it thirteen days later.

• For the later sowing on 26 May, Mace and Scepter had similar grain yield, however, protein was higher for Scepter.
• When sown early, Trojan had higher protein than Mace and Scepter.

A field trial was undertaken at Frances in 2019 to investigate combinations of barley sowing time, seed rate and herbicide treatments to control annual ryegrass. The average seedbank of annual ryegrass (ARG) at the site was quite low (472 ± 143 seeds/m2), which was reflected in low plant density at the site. ARG plant density was significantly influenced by the time of sowing (P=0.037), and herbicide treatment (P=0.009). There was a 37% reduction in ARG plant density between TOS 1 (20 plants/m2) and TOS 2 (13 plants/m2). Herbicide treatment had a significant effect on ARG plant density, with Boxer Gold showing lower efficacy on ARG than Treflan and Boxer Gold + Treflan. Unlike ARG plant density, ARG spike density was not influenced by time of sowing (P=0.171). ARG spike density was significantly influenced by barley seed rate (P=0.016), herbicide treatment (P=0.01) and the interaction between TOS and herbicide treatment (P=0.019). ARG spike density was 34% and 40% lower in medium and high seed rates respectively when compared to the low seed rate. These results suggest an improvement in ARG suppression from increasing barley competiveness with increased seed rate. Barley grain yield at the site averaged 6.6 t/ha. Herbicide treatment had a small (4-6%), but significant effect (P=0.009) on grain yield with Boxer Gold < Treflan ≤ Boxer Gold + Treflan for barley yield.

In this trial, there has been a positive response to phosphorus fertiliser applied at 9kg/ha at sowing and a positive response to nitrogen fertiliser applied at 20kg/ha. There has been a negative response to applied nitrogen both at sowing and top-dressing at higher than 20kg N/ha rates, which can be attributed to low growing season rainfall (GSR), which has occurred through prolonged periods over the course of the trial.

• Evidence from this trial indicates that further investigation of fluid fungicides banded at sowing for crown rot management is warranted.
• Many treatments decreased crown rot incidence early in the season and in these treatments, the plants had increased vegetative bulk later in the season.
• Fungicide application reduced levels of crown rot DNA in the crop at maturity.
• Expression of crown rot symptoms in durum wheat and bread wheat were different, depending on the treatment applied

• The early growth of the sub-tropical grasses (panic grass, Rhodes grass) was slow and they appeared to have cold stress.  The seedlings were cold stress with all three TOS and they took a while to recover.
• An interesting observation was that the surrounding paddock was sown to a sub-tropical grass mix (Gatton panic and Rhodes grass) just before the 3rd time of sowing, however the early growth of the perennial seedlings in the paddock was superior to the small plot trials.  Gatton panic is apomictic (i.e. all plants are essentially clones), so any difference must be due to the environment.  In this case, the markedly stronger early growth and less cold damage maybe due to the improved nutrition from the fertilizer applied at seeding. 
• To evaluate whether there was a nutrient deficiency an application of fertilizer - 150 kg/ha of DAP plus 100 kg/ha of MOP was applied to half of each rep in mid-December in a split plot design.  Subsequently there has been little rainfall, so no opportunity to measure a response.
• By mid-February there was not a substantial difference between the three times of sowing for Rhodes grass and Gatton panic which makes sense as in effect the sub-tropical grasses all emerged in early to mid-September for all three TOS.  The only species to emerge in any numbers before the third TOS was perennial veldt grass. However, by mid-February about 35-40% of the veldt grass plants had died and many more plants were highly stressed and may die over summer –autumn.  Sowing veldt grass in late winter – early spring with the sub-tropical grasses may not work in that persistence over summer may be poor.  Perennial veldt grass is a C3 so does not have the same soil temperature requirements as the sub-tropical grasses (C4).  An autumn sowing may be more successful for veldt grass.
• The results from the TOS at Eneabba in 2012 suggest little or no advantage in early sowing of sub-tropical grasses in early August.  The optimum sowing window appears to be late August with more flexibility with Rhodes grass than Gatton panic for early sowing. 

Sowing into moist soil improved crop emergence compared to dry soil, but did not increase yield.

Under low and variable ryegrass pressure, herbicides did not reduce overall ryegrass density, but did reduce inter-row ryegrass density.

There was no difference in efficacy between the 1.5L/ha and 3.0L/ha of TriflurX®.

• High operational speed reduced sowing depth of both disc and tyne openers.
• Counts of unsprayed (nil) annual ryegrass were greater for the tyne machine than the disc seeder at 8km/h and 14km/h.
• Within the applied herbicide treatments herbicide efficacy was fairly high. 
• all standing stubble and poor seed placement at 8km/h and 10km/h by the tyne machine severely affected crop establishment.
• At 14km/h the discs ability to penetrate the soil was greatly reduced, impacting sowing depth.
• Barley yields were higher for the disc sown treatments than the tyne sown treatments.

A combination of fertiliser inputs and irrigation can rapidly breakdownincorporated cereal stubble and allow sowing 4 weeks later. Getting the balance of fertiliser, in particular N rates, to ensure rapid breakdown, but creating neither N deficiency or excessive N remains elusive.

Measuring soil organic carbon following incorporation is giving mixed results as to the ability to increase soil OC via incorporation with fertiliser

Burning the stubble gave greater yield and oil content

There were no differences in medic regeneration in wheat stubbles either harvested at two heights, left standing or rolled.

Although there was a very late break to the season, cooler conditions through September and October
maintained good yields. There was a long period during flowering in October where no significant rainfall
fell. This limited yield potential and caused quite variable results. Annuello (at 3.0t/ha) (mid season
maturity), Whistler (at 3.0t/ha) (winter wheat) and Ventura (2.9t/ha) (short season maturity) were the highest
yielding varieties. While the long season varieties (like Rosella and Arrivato) were the lowest yielding

• Field peas have proven to be the most reliable pulse option on the upper Eyre Peninsula with yields remaining the most stable across seasons.
• Under favourable conditions there is potential for alternative pulse crops to be successful.
• Paddock selection, soil type, time of sowing, pulse agronomy, marketing and storage options all need careful consideration when looking at growing alternative pulse crops.
• New varietal options offer earlier maturity as well as improvements in harvestability, disease resistance and herbicide tolerance over older commercial standards, aiding production and profitability.
• Higher value alternatives, such as lentils, may be a high risk option and pulse crops better suited to the region could still prove to be the most profitable option in the long term.

• This and other research demonstrates that it is possible to improve crop establishment and productivity on water repellent soils using modified furrow sowing techniques.
• Banded wetting agents are helpful with early dry or partially dry sowing before opening rains but show less benefit later in the sowing program when there has already been rain and the soil has started to wet up more (see Banded wetting agent paper WMG 2012 research annual). In very erodible conditions with high wind erosion risk the use of this strategy may be safer than the options with winged points or boots due to less soil disturbance and release of root anchorage for existing plant cover. Optimal wetting agents for WMG areas still need identification.
• Winged points and winged-paired row systems perform better than knife points under certain soil conditions but the benefits are variable and in some sowing conditions may provide little benefit. Further research is required. Winged points look most attractive when shallow moist soil can be ‘delved’ to the seed zone to provide early establishment (as in the winged knife point on the gravelly sand with shallow moisture).
• Simple approaches like sowing next to or at a shallow angle across the previous year’s crop row and broadcast spreading a portion of the seed in front of the seeding tynes are relatively simple approaches that can provide establishment benefits.
•  

The dry September limited yields at this site, yields were about on par with the district, there was no difference between treatments at flowering or at any stage of growth. Available soil sulphur (S) at sowing was 55 kg/ha (taken to a depth of 35cm) and with a yield of 1.5 t/ha maximum, only 38kg S was required for the crop. This crop had enough soil sulphur already supplied before additional sulphur was applied.

• A single slug baiting was ineffective at controlling slug populations.
• Direct drilling into a heavy cereal stubble from a previous crop can result in significant slug damage to canola, even with a single baiting.
• Cereal stubble removal by burning, will significantly reduce the amount of slug damage.
• Cultivation prior to sowing will have a positive effect on reducing slug numbers and damage to canola.
• An integrated pest management approach is required to control slugs effectively. Each treatment alone does not adequately control slug populations.

There has been widespread use of continuous cereal in the Mallee over the past decade, and with many drought years throughout this period fertiliser inputs have generally been greater than crop demand. As a consequence, soil phosphoruslevels are often well above the critical level. By identifying soils and conditions where continuous cereal systems perform best and where inputs can be most effectively targeted, there is an opportunity to reduce input costs and increase profitability. This trial used PA methods to identify soil types for targeted soil sampling to achieve a greater understanding of soil phosphorus levels in different soil zones. Yield mapping was then used to identify if and where fertiliser applied to the crop impacted grain yield.

Key findings:

• Increasing levels of inoculum (oospores/ plant) of Phytophthora medicaginis (P. med) was strongly correlated with the decreasing yield of Yorker, a moderately resistant chickpea variety.
• An inoculum level of 660 oospores/plant (PreDicta B >5000 P. med copies/g soil) at sowing significantly reduced yield compared with lower inoculum levels under both dryland and irrigated conditions.
• These findings provide further evidence that the PreDicta B P. med test will be a useful tool for growers to determine their risk of Phytophthora root rot before sowing chickpeas.
• Note: the SARDI PreDicta B test for Phytophthora medicaginis is under development and is not yet available commercially.

Summary

P.med inoculum level, PRR disease and yield

Can the P.med DNA soil test predict the risk of Phytophthora root rot?  Based on the results of this trial with Yorker (MR) and the 2014 Tamworth trial with Sonali (S), the answer is YES.  For Yorker significant yield loss can be expected with starting (pre-sow sampling) inoculum levels above ca 3000 P.med DNA sequences/g soil (ca 130 oospores/plant). However, these values may need to be interpreted with some caution as seasonal conditions will modify outcomes, for instance in a dry season less disease may develop from the same amount of inoculum.

As Phytophthora can reproduce rapidly and cause new infections over a relatively short period there was concern that under PRR conducive conditions (a wet season), that low initial levels of inoculum could catch up to high initial levels as cause similar disease severity and yield loss.  The 2015 season was wet but not very wet, under these conditions there was separation in the disease and yields of the low and high inoculum treatments.

P.med DNA detection in commercial in paddocks and disease risk determination

These second season of detection capability results for the soil P.med DNA test were again generally promising, with most samples with positive and negative P.med DNA results corresponding to expected P.med isolation results.  However, results for some samples indicate that further work is required to a) identify what factors may contribute to false negative results and b) determine if false positives are due to the presence of dead or inactive P.med DNA

The DNA result for a soil sample from a paddock can only provide an indication of inoculum concentration and disease risk for the areas of the paddock which were sampled.  Therefore, the spread and locations of sampling across a paddock will affect how representative DNA results are for a paddock.  Because of the risk of rapid PRR disease buildup following wet conditions it may be appropriate to treat a negative Predicta B® test result as indicating a low risk rather than a nil risk, as the pathogen could still be in areas of the paddock that were not sampled and so still cause PRR and reduce yield. 

Work in 2016 will evaluate maximising the probability of detecting P. med by targeting those areas of the paddock where P.med is more likely to occur.  The pathogen thrives in high soil moisture contents and so often occurs in low lying regions of paddocks where pooling following rain may occur.  The pathogen also carries over from season to season on infected chickpea volunteers, lucerne and, native medics.  Including low lying areas and weedy areas of paddocks during PreDicta B® soil sampling may provide the best strategy to detecting P. med and so identifying a paddocks disease risk of PRR in chickpea.

• Grain yield was highest (5.8 t/ha) from Revenue and loest from Bass. Dry matter produciton was greatest from the barley lines as with the later sowing there was isufficient time for the other cereals to catch up.
• New barley germplasm from France is later flowering and has considerable potential for early sowing in the most frost prone areas of Tasmania. Both lines appear to possess some water logging tolerance.

• Grain yield was highest for Revenue and Endeavour (5.4 and 5.1 t/ha respectively) and lowest from Barley Z and Henley. Dry matter production was lowest from Revenue as with the water-logged conditions no third cut was taken.
• Winter barley germplasm is late flowering and may have considerable potential for early sowing in the more frost prone areas of Tasmania.
• There appears to be a strong interaction between grazing/cutting and water-logging with the additional stress of water-logging leading to poorer recovery after cutting.

• Bolta Balansa (3.2 t/ha DM), Lightening Persian (3.30 t/ha DM) and Elite II Berseem (2.94 t/ha DM) produced the highest amounts of DM at Dunkeld. 
• The site was somewhat a rundown pasture site, which go very wet in winter, and this did not favour Arrowleaf type cloers.
• Elite II provided good initial dry matter early - but then only provided extra dry matter with late rains. Persian clover only provided extra dry matter with late rain also.
• The Balansa clovers had superior growth in these conditions, with Bolta being the longer season type, providing more dry matter.

Application of DAP fertiliser at time of sowing improves yield in barley. Application of additional nitrogen lifts yields further, and improves protein levels in the grain. Results suggest efficiencies in nitrogen application can be achieved with placement in the root zone compared to surface application. Further work needs to be undertaken to better understand the process. 

Winter and spring wheat, barley, triticale and oat lines were evaluated for fodder dry matter production and grain yield. The two barley varieties and a spring wheat produced the highest dry matter (DM) in the first cut. However their recovery was poor and DM production from the second cut was significantly lower than for all other material.

• Two trials were conducted to compare dry matter production and subsequent grain yield from cereal crops. In one trial four cereal crop species wheat (Mackellar), barley (Urambie), triticale (Breakwell), and oats (Bass) were compared. With a longer vegetative period, a second DM cut was able to be taken from Bass oats and consequently total DM production was significantly higher than from Mackellar which in turn produced significantly more DM than Breakwell and Urambie. Grain yield was significantly higher from Breakwell (9.4 t/ha).
• In a second trial, 7 wheat varieties and breeding lines were compared. There were statistically no differences in DM production between the wheats. The CSIRO line 95102.1 and Alberic were the highest grain producers.

Mackellar wheat showed the most potential as a dual purpose crop with the highest grain yield and DM production comparable to all other varieties except Bass. The latter produced the most fodder but the lowest grain yield. There was no significant difference in DM
production between Mackellar, Breakwell, Urambie and Franklin however there was a large difference in when this was produced. Franklin barley (and a Chinese line) were far more vigorous early whereas the later developing varieties, in particular Bass, tended to produce less DM but extra cuts ensured a higher total DM.

• The European cultivars producted grain yields up to 4.78 t/ha.
• Grain yields from two of the European cultivars were significantly greater than Jardee TT but not significantly greater than Hyola 50 and 46Y83.
• The later maturity of the winter types may provide different management options to growers including grazing and time of sowing.
• Further testing of the European cultivars will need to be conducted over more locations and seasons and under different manangement to determine their potential for the HRZ.

Like many comments for 2008, the later break and well-below average rainfall in spring, saw disappointing  ield responses. In a better season, a winter cut followed by multiple measurements in the spring, would show some more promising yields (This would also assist in reducing variance within the trial, currently at 22%). Hardier plants such as oats and ryegrass were able to produce large amounts on lower amounts of rainfall, whilst shorter season annuals legumes such as vetch and arrowleaf clover had struggled to produce bulk, before flowering and before early December rains.

• A range of forage varieties were grown as rotational options atthe MFMG site at Frances and Conmurra. 
• At Conmurra and Frances,the highest DM producing forages were annual ryegrass; R2 tetrapkhid annual ryegrass (12.28 t/ha DM) at Conmurra and Grassmaar Diploid annual ryegrass  (7.53 t/ha DM), primarilty due to their ability for a winter cut. 
• The best annual clovers at both Conmurra and Frances include Zulu II Arrowleaf (6.46t/ha and 3.93t/ha) and Bolta Balansa (6.27t/ha and 4.11t/ha).
• The cereal/grass based options generally grew more DM and offered more competition but legume and broadleaf crops offered different herbicide options, disease breaks and in the case of legumes, nitrogen fixation. 
• The legume and brassica varieties produce forage of a higher quality than that of cerels and grasses, which provides greater benefit to grazing animals.
• More work required to show possible yields both as monocultures and as mixes for rotational options. 

• Pie-sowing treatments of trifluralin herbicide are effective in increasing yields in a barley crop infested with Vulpia. Application rates of 3.0 1/ha produced a significant result, while application rate of 1.5 1/ha produced a strong trend.
• No significant differences could be demonstrated between Post-sowing treatments employed in this trial due to large variations between plots. However averaged results indicate trends that can be further explored with more trial work. 
• For further conclusions please see the attached trial report.
   

Results from these trials indicate that lentils can be grown successfully on the lighter soils of the Birchip area. However, 1995 was a favourable year for lentil produciton and results should be noted with some caution.

1996 was characterised by a wet winter, frosts in spring and a dry finish.

• Soybean yield potential ranged from a low of 1.01 t/ha up to a high of 2.94 t/ha in two years of harvested irrigated variety evaluation experiments at Trangie in the Macquarie Valley.
• Delayed sowing of a soybean crop in the Macquarie Valley can increase the likelihood of delayed maturity, potentially running into prolonged periods of wet autumn weather at harvest time; the 2015–16 experiment was not able to be harvested for this reason.
• MoonbiA (released 2010) is the recommended variety for Macquarie Valley soybean growers under fully irrigated conditions. It has high yield potential, maturity adaptation, excellent grain quality to meet human consumption markets, and resistance to powdery mildew.
• Djakal (southern NSW variety) is recommended for partial irrigation or dryland situations. Its earlier maturity and lodging resistance due to shorter height and reduced biomass enables it to achieve high yields and human consumption quality under less favourable growing conditions.

• The best yielding winter cultivars yielded similar to the best yielding spring cultivars despite a month difference in flowering date.
• Winter barley shows promise but we are still learning.  Strategies utilising Nitrogen, Plant Growth Regulators and Grazing need development to manage the increased biomass production and to improve the conversion of biomass to grain yield
• Early sown winter barley is a different agronomic system. The farming system benefits of winter barleys such as grain and graze, improved disease resistance should not be overlooked
   

• Antas Sub clover (brachycalnium type) grew significantly more than other sub clovers, and more than twice the production of Trikkala (1.735t/ha DM)
• The more biomass you grow, the more nitrogen you fix. Using rules of thumb (25jg/ha N per 1t DM), Antas would fix 92kg/ha of nitrogen cf 43kg/ha N for Trikkala. 
• A later sowing combined with a dry spring produced some variances. and lower dm yields than expected. 
• More work is required to show possible yields, both as monocultures and as mixes for rotational options. 

Key messages:

• Treating EGA GregoryA seed with Rancona Dimension reduced establishment losses associated with the addition of crown rot inoculum to 7% compared with 26% when no seed treatment was used.
• In this instance, Rancona Dimension did not provide a significant or consistent yield benefit in the presence of high levels of crown rot infection across the 12 trial sites in 2015.
• Growers should not expect Rancona Dimension to provide a significant and consistent reduction in yield loss from crown rot infection when used as a standalone management strategy.
• Growers considering the use of Rancona Dimension should follow the manufacturer’s advice and only consider it as part of an integrated management strategy against crown rot.

Conclusions

Rancona® Dimension is registered in Australia for the suppression of crown rot infection. Rancona® Dimension reduced establishment losses associated with severe early infection, created by the addition of crown rot inoculum to the seed furrow at sowing, to 7% compared to 26% in the absence of a seed treatment. Further research is required to determine if this improvement in establishment is associated with reduced Fusarium seedling blight. It should also be established whether such severe establishment losses are an artefact of the inoculation process used in the trials or occurs naturally in paddocks with high stubble-borne inoculum loads. In a separate larger trial conducted at Tamworth in 2015 in which infected stubble at the surface was the inoculum source Rancona® Dimension did not have a significant impact on the establishment of EGA Gregory compared to the Nil seed treatment (data not presented). Establishment benefits apparent in the 12 trials unfortunately did not translate into any improvement in grain yield. Rancona® Dimension did not provide a significant yield benefit over the use of no seed treatment or the two other commonly used seed treatments examined in this study under high crown rot pressure across 12 sites in 2015.

Although Rancona® Dimension is registered for the suppression of crown rot, with activity against early infection and potential establishment losses evident in this study, growers should not expect this to translate into a significant and consistent reduction in yield loss from crown rot infection when the product is used as a standalone management strategy. Integrated management remains the best strategy to reduce losses to crown rot. Growers may like to consider including Rancona® Dimension (320 mL/100 kg seed) as one additional component in their integrated management of crown rot.

Sumemr fallow efficiencies at these sites were generally found to be within the range of 20 to 30%.

Averaged over all nitrogen treatments, there was no statistical difference between the 2 different plant populations in terms of yield or quality parameters, however the trends were identical to MacKellar: lower plant population 108 plants/m2 giving slightly lower yield (0.25 tlha) and higher protein.

• Seasonal conditions can affect the disease complexes that exist for sub-clovers in any season (eg. the drier summers in 2014 & 2015 would be expected to cause a higher incidence of Rhizoctonia, whereas the wetter season in 2016 saw Pythium sp., Aphanomyces sp. and Phytophthora sp. more likely to be the dominant diseases).
• Current sub-clover establishment management practices (knockdown herbicide, cultivation, use of Apron seed dressing and sowing newer varieties or those that are widely adapted to the region) appear to be reducing the risk posed by root disease across the region.

• Sowing late into a high disease burden may offset any benefits of varietal disease resistance or the benefits of chemical control methods (i.e. seed treatments).
• Seasonal conditions can affect the disease complexes that exist in any season (eg. the drier summers in 2014 & 2015 would be expected to cause a higher incidence of Rhizoctonia, whereas Pythium sp., Aphanomyces sp. and Phytophthora sp. are likely to be more dominant in wetter seasons).
• Varietal differences were observed in establishment and persistence, however it is yet to be determined if this was due to root disease tolerance.

• The timing of brownout had no significant effect on the germination rate. This may have been due to a simulated “cultivation” immediately prior to sowing.
• Significant differences were found in the germination levels between varieties; Woogenellup is an older variety that is thought to be more susceptible to root diseases. The varietal difference suggests that root disease may be an issue across the region.
• Demonstration site responses to metalaxyl seed treatments in sub-clover germination suggests that root disease may be present and affecting establishment and persistence.

• There is a range (from susceptible to moderately susceptible) in varietal resistance to eyespot in long season wheat varieties commonly grown in the South East. Although this range is small it is large enough to influence damage due to eyespot.
• Know the eyespot inoculum levels (which indicate the risk of yield loss) in paddocks being sown to cereals and use this information to assist in variety selection.
• Avoid sowing the susceptible varieties Wedgetail, Kiora and Forrest in paddocks which have high eyespot levels.
• Trojan, Brennan and Manning are generally more resistant (moderately susceptible) to eyespot than other varieties screened.

Findings are from one site in one season and more data will be needed before firm recommendations can be made.
• Where eyespot inoculum is present in paddocks at medium to high levels, avoid sowing Wedgetail and Orion. Trojan, Manning, and DS Pascal would be better choices, as would Compass if sowing a barley.
• Experience across 6 screening trials undertaken in SA in 2014 and 2015 indicates that some varieties (e.g. Trojan, Compass) are very consistent in their response to eyespot, but others (e.g.Hindmarsh, La Trobe, Corack, Shield) are not.
• Cereal types and varieties with weak straw are more likely to be at risk of lodging (and harvest difficulties) in the presence of eyespot than those which have good straw strength. Plant growth regulants might assist in reducing lodging issues.
• The range of susceptibilities shown within the varieties screened should provide a good base for breeding programs.

• Know the risk of yield loss from eyespot before sowing a cereal - inspect stem bases (lodging does not always occur) in a previous cereal crop or take soil samples pre-sowing and submit them to PreDicta B for analysis.
• Select less susceptible varieties which are well adapted to the area - untreated they will perform better and they may also be more responsive to fungicide application, particularly where disease pressure is high. Avoid varieties with weak straw strength as they are more likely to lodge when affected by eyespot.
• No fungicides are registered at present for eyespot management, but a number are in the process of registration. Once these are registered - use the correct rate (lower rates can be less effective); apply before canopy closure (GS30-31 is usually recommended); use high water rates; target the base of the plant.
• Delays (due to waterlogging) in fungicide application until after early stem elongation may reduce eyespot incidence and severity but may not give a yield response.
• Inoculum carryover is unlikely to be influenced by variety resistance alone but is likely to be reduced where a fungicide is applied prior to canopy closure. Greatest reductions in inoculum carryover were seen where two fungicide applications were made (tillering plus GS30-31) or where one fungicide application was made to a less susceptible variety.

Current projects are:

• Can adjusting zones within N1 paddock at Minnipa improve VRT outcomes?
• Small plot evaluation of the variable rate sowing paddock N1 at Minnipa
• Farming systems WUE survey 2010 – practices
• Responsive farming for soil type at Mudamuckla
• Responsive farming for soil type at Wharminda
• Manganese response in barley at Wharminda
• Can we reduce our phosphorus inputs?
• Crop production using replacement P
• Measuring the effect of residual P

The following series of articles are from trials undertaken in 2010 on the three focus sites:
• Responsive Farming Using Variable Rate Sowing at Minnipa
• Responsive Farming for Soil Type at Mudamuckla
• Responsive Farming for Soil Type at Wharminda
• Farming to Soil Potential on the Upper Eyre Peninsula: How Accurate was In-season Yield Prediction in
2010?
• Crop Production Using Replacement P Rates
• Measuring the Effect of Residual P
• Nitrogen Management on Upper Eyre Peninsula
• Wheat Variety Response to P on Grey Calcareous Soil

• Grain yields were increased by sowing early (mid-April to early-May) over later sowing (end of May) under the favourable growing seasons experienced at Hart in 2016, in contrast to similar climatic seasons in higher rainfall areas of SA such as Tarlee.
• Varieties with agronomic characteristics of early flowering and high biomass production optimised yields.
• There was no change in grain yields from application of plant growth regulators (PGRs) on early sown faba beans.
• Agronomic traits related to improved harvestability were observed from some PGRs, however further field testing will be required to better understand the best application timings and quantify benefits.

• Prices for faba beans have remained very high compared with long term averages, enhancing the profitability of faba beans. Growers always need to be aware of possible price swings as the international market is limited. The potential return for the crop should be based on longer term pricing between $300 and $400/ t.
• New varieties, PBA Zahra and PBA Samira, offer significantly improved grain yield (>10%) and disease resistance compared with older varieties.
• Sowing early is essential to maximise benefits to the farming system from improved biomass and grain yield to maximise profitability.
• Good disease management is critical to maximise grain yield and quality. Growers are encouraged to carefully plan their strategies, regularly monitor crops and have fungicide purchased in advance, to ensure appropriate timing of application.

• Early sowing, concurrent with previous research, was highest yielding in 2012
• There appear to be several promising new varieties available for southern Victoria, offering a range of grain types and forage options, associated with excellent yield potential.
• Crop topping results highlight the importance for growers and advisors to be aware of both weed and crop growth stages, otherwise significant grain yield loss could occur.

• A low level of rust infection occurred during October and was the only foliar disease affecting bean performance.
• 7% higher grain yields occurred in the fortnightly sprayed (improved rust control) and single
  cercospora treatment (reasons unclear) compared with the nil treatment.
• Grain yields decreased by 14% when sowing date was delayed from May 1 to May 18. No
  further yield loss occurred when sowing date was delayed to June 6.
• Nura was higher yielding than Farah at the mid sowing time and equal at the others, unlike
  in previous trials where Nura has been lower yielding at later sowing dates. Late rainfall events in 2007 were of more benefit to Nura than Farah.
• Necking (collapsing of top part of bean plant) was greater at the early sowing time. Nura
  had a higher level of necking than Farah sown early, but yields were the same. Similar
  necking and yield occurred between the two varieties when sown late.

• The three bean varieties, Farah, Fiesta and Nura, gave similar yields and showed a similar yield response to delayed sowing – i.e. around 1.5 t/ha when sown on May 12, falling to around 0.9 t/ha with a June 7 sowing.
• Foliar disease levels (ascochyta) were negligible in Farah and Nura at both sowing times, and very low in late sown Fiesta. The slightly higher, but still low, levels of ascochyta in early sown Fiesta were reduced by fungicide sprays, but this did not produce a yield response.
• Spinnaker herbicide applied at 100 g/ha post-sowing pre-emergence caused no yield depression in any of the varieties at either time of sowing, and showed no effect on total plant height or height to bottom pods at harvest.
• The extreme dry late winter/spring conditions may have limited responses to fungicide spray regimes and Spinnaker in this trial.

• Adding phosphorus (P) did not significantly increase yield or seed weight in the varieties PBA WardaA and PBA NasmaA.
• PBA NasmaA produced greater yield and seed size than PBA WardaA.

Conclusions:

In this experiment, additional P did not increase yield, however, on a lower P site, a positive response to P might occur. The reduction in yield caused by adding N might be due to reduced nodulation in N-treated plots, although nodulation was not measured in this trial. The greater yield and seed size of PBA NasmaA compared with PBA WardaA supports other experimental data.

• Visual observations of Spinnaker causing reduced bean growth were quite spectacular.
• The recommended maximum rate of Spinnaker (100 g/ha) suppressed growth and final grain yield in both Farah and Nura, and this was further exacerbated at higher rates and later sowing.
• The results do not show Nura to be more sensitive to Spinnaker than Farah overall, although Nura yields were reduced by Spinnaker at all sowing times, while Farah yields were only reduced at later sowings.

•Across all varieties tested, there was no significant response to sowing time, which validates the current sowing window recommendation. Therefore, the optimum time to sow faba bean at Lockhart in 2016 was late April–mid May.
• PBA Nasma and Fiesta VF were the two highest yielding commercial varieties.
• The advanced breeding lines AF10089 and AF09169, developed by Pulse Breeding Australia (PBA) were significantly higher yielding than all other varieties.
• PBA Samira and Nura yielded significantly higher when sown on 18 May compared to 28 April.
• Crop lodging was significantly less for the 18 May sowing date.
• PBA Nasma flowered 17 and 14 days earlier than PBA Samira and PBA Zahra at 28 April, and eight and six days earlier at 18 May.

• The optimum time to sow faba beans in southern NSW was late April–mid May.
• Even in a favourable season such as 2016 there was a 10% yield penalty when sowing was delayed from 7 May to 2 June.
• Average seed size reduced by 8% when sown outside the recommended window.
• PBA Nasma, Fiesta VF, and PBA Zahra were the highest yielding commercial varieties.
• Advanced breeding lines AF10089 and AF09169 had significantly higher grain yields, particularly at the 28 April sowing date when compared to other sowing dates.
• Flowering duration for PBA Samira and PBA Zahra was stable across sowing dates, but reduced for PBA Nasma as sowing was delayed.

• Plant height was shorter than normal for the Tarlee area, likely due to the drier than average spring in 2012.
• A plant density x variety response showed that Fiord was the only variety to show decreased plant height with increasing plant density.

• Despite relatively low growing season rainfall in 2012, bean yields were still reasonably high at Bool Lagoon in 2012. It is likely that yields were buoyed by high December 2011 rainfall, lack of disease, and the relatively mild (although dry) finish to the 2012 season.

• Sowing early (April 26) produced the highest grain yields in 2018.
• In a drier than average year there was a yield benefit from very high sowing rates on narrow row spacings, with significant gains from 21 to 31 plants/m2, and from 31 to 45 plants/m2.
• 2018 was a low disease year and there was no disease penalty from higher sowing rates. Yield benefits from higher plant densities should be weighed against higher disease risks in wetter years. 

• The optimum timing to sow faba beans at Junee in 2015 was mid-April.
• PBA Zahra, PBS Samira and PBA Nasma were the highest yielding varieties.
• Commercial yields of 3t/ha are acheivable with appropriate variety and selection management. 

• Th optimum time to sow faba beans at Lockhart in 2015 was mid-Apri.
• PBA NAsma, PBA Samira and Fiesta VF were the highest yielding commercial varieties.
• The 23 April sowing had a mean bottom pod height of 42.3cm, 29% higher than the 13 May sowing.

• Sowing time has far greater consequences on growth, development, dry matter and grain yield of faba bean than variety choice.
• The dry spring combined with temperature constraints, imposed a common ceiling to yield despite large differences measured in dry matter (DM), height and reproductive number across all treatments.
• Early sown faba bean was primarily affected by severe frosts, while later sown was limited by flower node production and heat stress.
• Under these conditions, early April sowings resulted in greater biomass, taller plants, more flowering nodes, additional lodging, more disease and greater frost damage. Given a more favourable spring, disease and lodging could have been further exacerbated, inflicting even greater yield penalties to the first time of sowing (TOS).
•  Findings from this and previous experiments show the optimum sowing window for faba bean on acidic, red brown soils of southern NSW to be from 20 April to 15 May. The later sown crops within this window could still be disadvantaged under early unfavourable finishing conditons. 

• The optimum time to sow faba beans at Wagga Wagga in 2015 was mid-late April.
• PBA Nasma, PBA Samira, PBA Zahra, Farah and Fiesta VF were the highest yielding commercial varieties.
• Time of sowing had a far greater effect on growth, development and grain yield, of faba bean than variety in this experiment.
• PBA Nasma prduced a small grain size of 53g/100 seeds, which could have negative marketing implications. Further testing is required to determine if this was a seasonal effect.

• Winter and early spring seasonal conditions favoured faba bean production in 2009, and yields were more than double those in 2008.
• Yield was generally maximised at the early sowing date and at the narrow row spacing.
• Farah was the highest or equal highest yielding variety at both sowing dates in 2009.
• The taller varieties Farah and 974* showed the largest reduction in yield when row spacing
  was doubled from 9” to 18”.
• Chocolate spot levels were high in 2009, and accounted for 32% yield loss across varieties
  in untreated plots. Agronomic techniques that delayed canopy closure (ie later sowing, lower
  plant densities and wider row spacings) were important in reducing disease severity.
• Nura had higher disease levels and lower grain yield than Fiesta across all treatments in
  2009, but a triple chocolate spot spray strategy was effective in reducing yield loss by 25%
  in both varieties.
• Decreasing plant density was the most significant factor influencing disease levels after
  delayed sowing, and resulted in lower disease levels across all varieties, and increasing row
  spacing reduced disease infection in early sown Fiord only.
• Increasing row spacing reduced chocolate spot infection, but only in the susceptible variety
  Fiord when sown early.

• Grain yields of beans were lower in 2012 in than previous seasons, averaging 3.6t/ha at Bool Lagoon.
• All varieties showed higher yields sown early.
• Later maturing varieties PBA Rana and PBA Kareema performed similarly to other varieties in this trial in 2012, despite the low season rainfall.
• The three earlier maturing varieties (Farah, Fiord and Nura) showed increased yield from increasing plant density, while no yield response was seen in later maturing and larger seeded varieties (PBA Rana and PBA Kareema).
• Fiord showed the most response from varying plant density across the three seasons of trials.
• Crop-topping trials showed a 9% yield loss across all varieties from crop-topping at the milky dough stage of ryegrass in 2012 and caution is required with this practice in later maturing regions. No yield loss was generated from later treatments.

• Plant densities greater than 25 pl/m2 produced the highest grain yields in 2018.
• PBA Samira and PBA Zahra performed equally well, with average grain yield of 3.2 t/ha and 3.1 t/ha, respectively.
• 2018 was a low disease year and there was no disease penalty from higher sowing rates. Yield benefits from higher plant densities should be weighed against higher disease risks in wetter years. 

• Despite a dry season, yields for many of the varieties was extremely good, with Aquadulce and Fiesta VF both performing well. Manafest did not perform well in this trial, although in the intermediate trial at the same site, it yielded much better and was not significantly different in yield to Aquadulce. 
• Dry conditions at sowing limited the effectiveness of the post sowing pre-emergent herbicide sprays used. This is a major constraint with growing beans as there are no broadleaf herbicides registered for use post emergent in beans. Beans are best grown as a third or fourth crop in the rotation, after broadleaf weeds have been controlled in previous years. 

• Inoculating faba beans prior to sowing improved nodulation on acid soil.
• New acid tolerant rhizobia (strain SRDI-969) increased nodulation but not grain yield, which was limited by low rainfall.
• The SRDI-969 is a promising strain, which is under evaluation as a future replacement for the current commercially available strain (WSM-1455).

• In a season with very little disease pressure, small varietal differences in chocolate spot did occur throughout the season, but these differences did not manifest into yield differences. Seed rate was critical to maximise yield in 2020, where lower seeds rates produced significantly lower yields when compared to higher seed rates. Seed rates also had a major effect on crop architecture, with lower seed rate treatments podding over a longer portion of the stem and having a higher pod number but lower overall dry matter harvest than that of higher seed rates.

 

• In 2020 grin yields were high (3.36 and 2.96 t/ha) considering the dry finish to the season. As with the sowing rate trial, varieties that were slower to mature and held a green canopy for longer and could not convert the green leaf area into yield due to the very dry spring conditions Variety selection is the key to minimise diseases. However, in low disease pressure situations, less disease doesn’t mean higher yields.

The irrigated spring-sown faba beans produced higher yields with an average of 6.9 t/ha across the treatments (Table 3). High variability in the trial suggests these numbers may be exaggerated, but header data from the surrounding paddock indicate that up to 6 t/ha grain yields were achieved by the grower in some parts of the paddock.

Applying inoculant at sowing has proven to be beneficial to early season crop vigour in faba bean production. Adequate phosphorus fertiliser increased early season crop vigour, biomass and grain yields. Applying 75 kg/ha MAP to faba bean at sowing doubled biomass production compared to faba bean being sown with no fertiliser, at Strawberry Hill in 2019.

• Grain yields were low and variable in 2018 due to low soil pH at the site, and waterlogging that occurred during winter. The removal of molybdenum from the fertiliser significantly reduced plant vigor and grain yield. However, due to the high soil variability results should be treated with caution. 
   

Potassium applied to faba bean at sowing and/or at flowering had no effect on plant height, biomass or grain yield.

Tebuconazole foliar fungicide is the superior treatment for controlling this disease, showing that Systiva® seed treatment or Uniform® in furrow were not effective fungicide treatments for control of cercospora leaf spot. 182 Infection from cercospora leaf spot was high early in the season at eight node stage where Uniform mildly suppressed severity compared to the nil treatment. However, by spring the standard tebuconazole treatment at six node growth stage prevented further spread of the disease.

The grain yield of faba beans significantly increased at higher plant densities especially when the when the diseases were controlled. Despite a late autumn break, with adequate chemical disease control, PBA Samira grain yields more than tripled (from 1.5 t/ha to 5.4 t/ha) when plant densities increased from 5 plants/m2 to 45 plants/m2 at Tarrington in 2019.

In 2019 at Lake Bolac, faba bean grain yield was reduced by 15% when the crop emerged on June 12 compared to May 23. PBA Zahra and PBA Nasma had larger seed sizes than PBA Samira and PBA Marne.

AF12025 and PBA Nasma, which are varieties with shorter season length outperformed varieties with longer season lengths (PBA Samira and PBA Bendoc) when sown in spring.

• The optimum time to sowing faba bean at Junee in 2015 was mid-April.
• PBA Zahra, PBA Samira and PBA Nasma are the highest yielding varieties.
• Commercial yields of 3 t/ha are achievable with appropriate varieties and management.

• The optimum time to sowing faba bean at Wagga Wagga 2015 was mid-late April.
• PBA Nasma, PBA Samira, PBA Zahra, Farah and Fiesta VF were the highest yielding commercial varieties.
• Choice of sowing time had far greater consequences on growth, development and grain yield of faba bean than choice of variety in this experiment.
• PBA Nasma produced a small grain size of 53 gm/100 seeds which may have negative marketing implications

Group B herbicide application timing significantly influenced plant height, biomass and grain yield of faba bean varieties. The level of herbicide damage and subsequent yield losses from the herbicide treatments were generally more severe in PBA Samira than PBA Bendoc, and when applied incrop than PSPE. PBA Samira incurred significant yield loss from all the herbicide treatments except SU1 applied at PSPE and Imi2 applied at PSPE and flowering. In contrast, PBA Bendoc showed improved tolerance and did not have significant yield loss from most herbicide treatments except in-crop application of SU2 and SU1.

• In the southern Victorian Mallee environment, grazing crops intended for grain production can be risky, with potential penalties to grain yield and/or quality.
• The success of grazing crops relies on an early sowing opportunity and good spring.

• This work summarises the experiences of seven farmers grazing winter cereals across four different types of enterprise.
• The economic benefits were positive in all cases and ranged from $10.80/ha to $84.06/ha. When comparative grain yields were also included, this range became $21.56/ha to $430.80/ha.
• For further findings please see the attached trial report.

The four farmer demonstrations showed

• By sowing a cereal into established lucerne, total winter production can be increased although lucerne production will be decreased.
• Variety and cultivar selection is important to match growth to animal demand.

o Spring wheat, oats or barley suit early production.
o Winter wheat suits extended production.
o Barley can be used for grain production.

• Different types of sowing machinery can be used successfully.
• Live weight gains in excess of 200grms/day/hd can be achieved at a period when pasture is usually in short supply
• A viable grain yield can be achieved under good seasonal conditions by using barley.

Six different farmer operated seeders were used in a minimum tillage situation to compare seeder set up and the effect of trifluralin incorporated by sowing on crop emergence. The demonstrations were taken through to harvest to compare yield.

The drought of 2002 continued to impact on sheep production in early 2003 through a lack of bulk in crop stubbles and a high erosion risk if these stubbles were grazed. Breeding ewes were retained in the Hungry Sheep system using containment areas to avoid erosion problems and to maintain ewes. No other system contained significant sheep numbers during 2003. July-dropped crossbred lambs grazed on medic pasture and reached a weight of 45kg in mid-December. The ewes received no supplementary feeding from July, at a stocking rate of 3.7 ewes/ha. This was largely due to early germination of medic pasture in February, and sufficient follow-up rain to keep some plants alive, producing adequate pasture in late autumn/winter. Regenerating pastures were more productive than pastures sown at the autumn break.

• Reliance on chemicals as the only weed control option is difficult (almost impossible) in a run of dry years.
• This trial will cease at the end of 2004 (3 years too early to obtain meaningful results) unless other funding is found.
• The trial showed, in the 2003 season, that there was no yield penalty for waiting until rain for sowing, although grain protein was lower in these crops.

• Crop yields in 2006 were driven by fallow (no difference between mechanical/conventional).
• Early sowing set an upper limit to yield but did not compensate for not being sown on fallow.
• Crop emergence was very sensitive to sowing conditions, with later sowing and sowing into 2005 cereal crop stubbles leading to much later crop emergence.
• The difference in soil available water driving the fallow response was difficult to measure with soil sampling on these soils; soil available nitrogen was a better predictor of yield in 2006.
• There were no yield penalties to adopting no-till in the Hungry Sheep and Fuel Burner systems.
• Cultivation in No Till and Reduced Till paddocks produced inconsistent effects on yield.